ROME, NY —
OSHA Inspection: INTERNATIONAL WIRE GROUP, INC., BARE WIRE DIVISION
Planned inspection · Safety discipline
At a glance
On , OSHA opened a planned safety inspection of INTERNATIONAL WIRE GROUP, INC., BARE WIRE DIVISION in 900 RAILROAD STREET, ROME, NY 13440 (NAICS 331421). OSHA activity number 339829657.
OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- INTERNATIONAL WIRE GROUP, INC., BARE WIRE DIVISION
- Site address
- 900 RAILROAD STREET
- City
- ROME
- State
- NY
- ZIP
- 13440
- Mailing
- P.O. BOX 131, CAMDEN, NY 13316
What kind of inspection was it?
- Inspection type
- Planned (H)
- Scope
- Complete (A)
- Discipline
- Safety
- Advance notice
- No
- Union status
- B
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 331421
- Employees
- 65
- Ownership type
- A
Citations
6 citations on file for this inspection.
1910.23 C01
- Issued
- Jul 7, 2014
- Abate by
- Jul 25, 2014
- Penalty
- Initial $3,400 · Current $2,040 Reduced
General-duty citation text
29 CFR 1910.23(c)(1): Open-sided floors and/or platforms four feet or more above adjacent floor or ground level were not guarded with standard railings (or equivalent) and toeboards:Note: Toeboards are only required when persons can pass, there is moving equipment or there is equipment with which falling materials could create a hazard. a) Rod Plate Area, on or about 6/27/14: Work platform was not provided with standard railings. Employees were exposed to a 9 foot 4 inch fall hazard.
Recent events (2)
- — I (S) $2040
- — Z (S) $3400
1910.212 A01
- Issued
- Jul 7, 2014
- Abate by
- Aug 9, 2014
- Penalty
- Initial $3,400 · Current $2,040 Reduced
General-duty citation text
29 CFR 1910.212(a)(1): One or more methods of machine guarding was not provided to protect the operator and other employees in the machine area from hazards such as those created by point of operation, ingoing nip points, rotating parts, flying chips and sparks: a) Lower Maintenance, on or about 6/27/14: Bridgeport milling machine was used without a guard to prevent contact with the rotating chuck and cutting bit. b) Maintenance, on or about 6/27/14: Delta single spindle drill press was used without a guard to prevent contact with the rotating chuck and cutting bit.
Recent events (2)
- — I (S) $2040
- — Z (S) $3400
1910.219 C02 I
- Issued
- Jul 7, 2014
- Abate by
- Jul 25, 2014
- Penalty
- Initial $3,400 · Current $0 Reduced
General-duty citation text
29 CFR 1910.219(c)(2)(i): All exposed part(s) of horizontal shafting seven (7) feet or less from floor or working platform were not protected by stationary casing(s) enclosing shafting completely or by trough(s) enclosing sides and top or sides and bottom of shafting: a) Laribee Hard Rod Area, on or about 6/27/14: Laribee Hard Rod #101-01R had a horizontal rotating shaft that was not adequately guarded.
Recent events (2)
- — I (S) $0
- — Z (S) $3400
1910.219 C03
- Issued
- Jul 7, 2014
- Abate by
- Jul 25, 2014
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.219(c)(3): Vertical or inclined shafting seven -7 feet or less from floor or working platform was not enclosed with stationary casing(s): a) Rod Plate Area, on or about 6/27/14: Electroplater #305-01-R had a vertical drive shaft that was not adequately guarded.
Recent events (2)
- — I (S) $0
- — Z (S) $0
1910.219 D01
- Issued
- Jul 7, 2014
- Abate by
- Jul 25, 2014
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.219(d)(1): Pulley(s) with part(s) seven feet or less from the floor or work platform were not guarded in accordance with the requirements specified in 29 CFR 1910.219(m) and (o): a) Laribee Hard Rod Area, on or about 6/27/14: Belt and pulley drive was not adequately guarded in that the portable guard provided did not prevent access to the hazard area.
Recent events (2)
- — I (S) $0
- — Z (S) $0
1910.219 E01 I
- Issued
- Jul 7, 2014
- Abate by
- Jul 25, 2014
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.219(e)(1)(i): Horizontal belts which had both runs 42 inches or less from the floor level were not fully enclosed by guards conforming to requirements specified in 29 CFR 1910.219(m) and (o): a) Laribee Hard Rod Area, on or about 6/27/14: Laribee Hard Rod machine #101-01R, belt and pulley drive was not adequately guarded.
Recent events (2)
- — I (S) $0
- — Z (S) $0
More inspections in this industry (NAICS 331421)
More inspections in NY
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 339829657.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.