Safety Incidents OSHA Severe Injury Reports · 2015–2025
5,194,531Inspections Most recent open 2026-08-11 Last loaded 2026-08-14

OSHA Inspection: APEX PLASTIC FINISHING CO.

Complaint inspection · Health discipline

On , OSHA opened a complaint health inspection of APEX PLASTIC FINISHING CO. in 1040 INDUSTRIAL DR., BENSENVILLE, IL 60106 (NAICS 326199). OSHA activity number 339848962.

What this inspection record means

OSHA opens inspections for many reasons: routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.

Watch Apex Plastic Finishing CO. for free Get an email when a new federal OSHA severe-injury report for Apex Plastic Finishing CO. is published. One employer, no account, unsubscribe in one click.
Site address
1040 INDUSTRIAL DR.
City
BENSENVILLE
State
IL
ZIP
60106
Mailing
1040 INDUSTRIAL DR., BENSENVILLE, IL 60106
Inspection type
Complaint (B)
Scope
Partial (B)
Discipline
Health
Advance notice
No
Union status
B
Opened
Closing conference
Case closed
Last modified
Data loaded
NAICS code
326199
Employees
46
Ownership type
A

5 citations on file for this inspection.

1910.133 A01

Serious Gravity 1 1 instance 2 exposed
Issued
Dec 12, 2014
Abate by
Dec 24, 2014
Penalty
Initial $2,100 · Current $1,470 Reduced
29 CFR 1910.133(a)(1):   The employer did not ensure that each affected employee uses appropriate eye or face protection when exposed to eye or face hazards from flying particles, molten metal, liquid chemicals, acids or caustic liquids, chemical gases or vapors, or potentially injurious light radiation:  Employees working on the "hand paint" lines spray painting parts were not using appropriate eye protection to protect them from solvent-based paint overspray.  Abatement certification is required of this item in accordance with the requirements of 29 CFR 1903.19(c).
Recent events (2)
  • · I (S) $1470
  • · Z (S) $2100

1910.134 C01

Serious Gravity 5 1 instance 2 exposed
Issued
Dec 12, 2014
Abate by
Feb 2, 2015
Penalty
Initial $2,800 · Current $1,960 Reduced
29 CFR 1910.134(c)(1):   A written respiratory protection program that included the provisions in 29 CFR 1910.134(c)(1)(i) - (ix) with worksite specific procedures was not established and implemented for required respirator use:  Employees working on the "hand paint" lines spray painting parts are required by the employer to wear half mask elastomeric type respirators with cartridge filters. The employer did not establish and implement a written respiratory protection program.  Abatement certification is required of this item in accordance with the requirements of 29 CFR 1903.19(c).
Recent events (2)
  • · I (S) $1960
  • · Z (S) $2800

1910.134 E01

Serious Gravity 5 1 instance 2 exposed
Issued
Dec 12, 2014
Abate by
Feb 2, 2015
Penalty
Initial $0 · Current $0
29 CFR 1910.134(e)(1):   The employer did not provide a medical evaluation to determine the employee's ability to use a respirator, before the employee was fit tested or required to use the respirator in the workplace:  Employees working on the "hand paint" lines spray painting parts are required by the employer to wear half mask elastomeric type respirators with cartridge filters. The employer did not provide a medical evaluation to determine the employees' ability to use a respirator.  Abatement certification is required of this item in accordance with the requirements of 29 CFR 1903.19(c).
Recent events (2)
  • · I (S) $0
  • · Z (S) $0

1910.134 F02

Serious Gravity 5 1 instance 2 exposed
Issued
Dec 12, 2014
Abate by
Feb 2, 2015
Penalty
Initial $0 · Current $0
29 CFR 1910.134(f)(2):   Employee(s) using tight-fitting facepiece respirators were not fit tested prior to initial use of the respirator:  Employees working on the "hand paint" lines spray painting parts are required by the employer to wear half mask elastomeric type respirators with cartridge filters. The employer did not provide fit testing prior to initial use of the respirators.  Abatement certification is required of this item in accordance with the requirements of 29 CFR 1903.19(c).
Recent events (2)
  • · I (S) $0
  • · Z (S) $0

1910.132 D02

Other-than-serious 1 instance 44 exposed
Issued
Dec 12, 2014
Abate by
Feb 2, 2015
Penalty
Initial $0 · Current $0
29 CFR 1910.132(d)(2):   The employer did not verify, through a written certification, that the required workplace hazard assessment had been performed:  The employer did not have a written certification to demonstrate that the required workplace hazard assessment had been performed.  Abatement certification is required of this item in accordance with the requirements of 29 CFR 1903.19(c).
Recent events (2)
  • · I (O) $0
  • · Z (O) $0

View Apex Plastic Finishing CO.'s full OSHA safety record →

This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 339848962.

Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.