NORTH BRANFORD, CT —
OSHA Inspection: TOTAL EXTERIORS LLC
Unprogrammed Other inspection · Safety discipline
At a glance
On , OSHA opened an unprogrammed Other safety inspection of TOTAL EXTERIORS LLC in 278 NOTCH HILL RD RTE 22, NORTH BRANFORD, CT 06471 (NAICS 238160). OSHA activity number 339874026.
OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- TOTAL EXTERIORS LLC
- Site address
- 278 NOTCH HILL RD RTE 22
- City
- NORTH BRANFORD
- State
- CT
- ZIP
- 06471
- Mailing
- 133 PINE ORCHARD RD, BRANFORD, CT 06405
What kind of inspection was it?
- Inspection type
- Unprogrammed Other (I)
- Scope
- Partial (B)
- Discipline
- Safety
- Advance notice
- No
- Union status
- B
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 238160
- Employees
- 2
- Ownership type
- A
Citations
6 citations on file for this inspection.
1926.300 A
- Issued
- Sep 30, 2014
- Abate by
- Oct 20, 2014
- Penalty
- Initial $1,200 · Current $600 Reduced
General-duty citation text
29 CFR 1926.300(a): Hand tool(s), power tool(s) or similar equipment were not maintained in a safe condition: Location: 278 Route 22 (Notch Hill Road), North Branford, CT 06471 The power cord on the DeWalt 7 1/4 inch circular saw, model DW368, serial #64585, used to cut the 3/4 inch thick plywood sheathing was frayed and repaired with black tape.
Recent events (2)
- — I (S) $600
- — Z (S) $1200
1926.404 B01 I
- Issued
- Sep 30, 2014
- Abate by
- Oct 20, 2014
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1926.404(b)(1)(i): Employer did not use either ground fault circuit interrupters as specified in paragraph (b)(1)(ii) of this section, or an assured equipment grounding conductor program as specified in paragraph (b)(1)(iii) of this section to protect employees on construction sites. Location: 278 Route 22 (Notch Hill Road), North Branford, CT 06471 Dewalt 7 1/4 inch circular saw, model DW368,serial #64585, used to cut 3/4 inch thick plywood was not protected by an assured equipment grounding program or a ground fault circuit interrupter.
Recent events (2)
- — I (S) $0
- — Z (S) $0
1926.501 B13
- Issued
- Sep 30, 2014
- Abate by
- Oct 20, 2014
- Penalty
- Initial $2,000 · Current $1,000 Reduced
General-duty citation text
29 CFR 1926.501(b)(13): Each employee(s) engaged in residential construction activities 6 feet (1.8 m) or more above lower levels were not protected by guardrail systems, safety net system, or personal fall arrest system, nor were employee(s) provided with an alternative fall protection measure under another provision of paragraph 1926.501(b). Location: 278 Route 22 (Notch Hill Road), North Branford, CT 06471 The 8 in 12 pitch roof with a 12 foot eave to ground fall distance on the front side (street side) of the structure was not equipped with a fall protection system.
Recent events (2)
- — I (S) $1000
- — Z (S) $2000
1926.503 A01
- Issued
- Sep 30, 2014
- Abate by
- Nov 2, 2014
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1926.503(a)(1): The employer did not provide a training program for each employee potentially exposed to fall hazards to enable each employee to recognize the hazards of falling and the procedures to be followed in order to minimize these hazards: Location: 278 Route 22 (Notch Hill Road), North Branford, CT 06471 A training program for each employee exposed to falls was not developed and implemented to train each employee to recognize hazards associated with fall hazards and the procedures to minimize and/or eliminate those hazards.
Recent events (2)
- — I (S) $0
- — Z (S) $0
1926.1053 B01
- Issued
- Sep 30, 2014
- Abate by
- Oct 20, 2014
- Penalty
- Initial $2,000 · Current $1,000 Reduced
General-duty citation text
29 CFR 1926.1053(b)(1): Portable ladders were used for access to an upper landing surface and the ladder side rails did not extend at least 3 feet (.9 m) above the upper landing surface to which the ladder was used to gain access. Location: 278 Route 22 (Notch Hill Road), North Branford, CT 06471 The side rails of the Louisville Type II Aluminum Ladder model # L-2223-2A used to gain access to the front street side of the roof did not extend at least 3 feet above the roof brackets/upper landing surface of the roof.
Recent events (2)
- — I (S) $1000
- — Z (S) $2000
1926.1060 A
- Issued
- Sep 30, 2014
- Abate by
- Nov 2, 2014
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1926.1060(a): The employer did not provide a training program for each employee using ladders and stairways, as necessary, which would enable each employee to recognize hazards related to ladders and stairways and train each employee in the procedures to be followed to minimize these hazards. Location: 278 notch Hill Road (Route 22), North Branford, CT 06471 A training program was not developed and implemented for each employee utilizing portable ladders in order to instruct each employee to recognize hazards related to portable ladders and the means/procedures to minimize and/or eliminate those hazards.
Recent events (2)
- — I (S) $0
- — Z (S) $0
More inspections at Total Exteriors LLC
View Total Exteriors LLC's full OSHA safety record →
More inspections in this industry (NAICS 238160)
More inspections in CT
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 339874026.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.