THEODORE, AL ·
OSHA Inspection: ALABAMA ROLL, INC.
Planned inspection · Health discipline
At a glance
On , OSHA opened a planned health inspection of ALABAMA ROLL, INC. in 5350 LAURENDINE RD., THEODORE, AL 36582 (NAICS 332114). OSHA activity number 339894800.
OSHA opens inspections for many reasons: routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- ALABAMA ROLL, INC.
- Site address
- 5350 LAURENDINE RD.
- City
- THEODORE
- State
- AL
- ZIP
- 36582
- Mailing
- 5350 LAURENDINE RD., THEODORE, AL 36582
What kind of inspection was it?
- Inspection type
- Planned (H)
- Scope
- Complete (A)
- Discipline
- Health
- Advance notice
- No
- Union status
- B
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 332114
- Employees
- 13
- Ownership type
- A
Citations
3 citations on file for this inspection.
1910.23 C01
- Issued
- Oct 17, 2014
- Penalty
- Initial $1,360 · Current $1,360
General-duty citation text
29 CFR 1910.23(c)(1): Open-sided floors and/or platforms four feet or more above adjacent floor or ground level were not guarded with standard railings (or equivalent) and toeboards:Note: Toeboards are only required when persons can pass, there is moving equipment or there is equipment with which falling materials could create a hazard. a) Behind the Haeusler 4-Roll Plate Bending Machine; on or about August 12, 2014 and times prior the employer exposed his employees to falls of 6.7 feet by not providing a standard railing or equivalent around the machinery pit.
Recent events (2)
- · I (S) $1360
- · Z (S) $1360
1910.252 B04 IV
- Issued
- Oct 17, 2014
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.252(b)(4)(iv): An attendant with a preplanned rescue procedure was not stationed outside a confined space opening to observe the welder at all times in case of emergency: a) Welding shop area beside north exit door; on or about August 12, 2014 and times prior the employer did not provide an outside attendant to observe the welder required to weld inside a 4 foot by 10 foot tube with only one opening.
Recent events (2)
- · I (O) $0
- · Z (O) $0
1910.305 G02 III
- Issued
- Oct 17, 2014
- Abate by
- Oct 29, 2014
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.305(g)(2)(iii): Flexible cords and cables were not connected to devices and fittings so that strain relief was provided that would prevent pull from being directly transmitted to joints or terminal screws: a) Portable electric shop fan near North exit door in welding shop; On or about August 12, 2014 and times prior the employer exposed his employees to electric hazards in that a 120 V cord was improperly installed into a male plug. The outer insulation had been cut back so far, leaving the inner conductors in the area of the male plug that squeezes the cord and acts as strain relief, with the outer insulations cut back so far the outer diameter of the cord was too small for the plug to cinch to in order to provide strain relief.
Recent events (2)
- · I (O) $0
- · Z (O) $0
More inspections in this industry (NAICS 332114)
More inspections in AL
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 339894800.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.