Safety Incidents OSHA Severe Injury Reports · 2015–2025
5,189,992Inspections Most recent open 2026-07-18 Last loaded 2026-07-22

OSHA Inspection: KENCO, INC

Planned inspection · Health discipline

On , OSHA opened a planned health inspection of KENCO, INC in 5757 NORTH MCRAVEN ROAD, JACKSON, MS 39209 (NAICS 423310). OSHA activity number 340139583.

What this inspection record means

OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.

Watch Kenco, INC — free Get an email when a new federal OSHA severe-injury report for Kenco, INC is published. One employer, no account, unsubscribe in one click.
Establishment
KENCO, INC
Site address
5757 NORTH MCRAVEN ROAD
City
JACKSON
State
MS
ZIP
39209
Mailing
P.O. BOX 7538, JACKSON, MS 39284
Inspection type
Planned (H)
Scope
Partial (B)
Discipline
Health
Advance notice
No
Union status
B
Opened
Closing conference
Case closed
Last modified
Data loaded
NAICS code
423310
Employees
9
Ownership type
A

9 citations on file for this inspection.

5(a)(1)

Serious Gravity 5 2 instances 2 exposed
Issued
Feb 27, 2015
Abate by
Mar 3, 2015
Penalty
Initial $2,000 · Current $1,080 Reduced
OSH ACT of 1970 Section 5(a)(1): Public Law 91-596, the Occupational Safety and Health Act of 1970, Section 5(a)(1):  The employer did not furnish to each of his employees employment and a place of employment which were free from recognized hazards that were causing or are likely to cause death or serious physical harm to his employees, in that employees were exposed to: struck by or crushed hazard in the event that the forklift overturns.    (a) Woodworking Area - On or about December 10, 2014 the forklift driver did not wear a seat belt while operating a Toyota forklift.
Recent events (2)
  • — I (S) $1080
  • — Z (S) $2000

1910.23 D01 II

Serious Gravity 5 1 instance 1 exposed
Issued
Feb 27, 2015
Abate by
Mar 11, 2015
Penalty
Initial $1,600 · Current $864 Reduced
29 CFR 1910.23(d)(1)(ii): Stairway(s) less than 44 inches wide having one side open, did not have at least one stair railing on the open side:    (a) Holtec Saw - On or about December 10, 2014 the employer did not installed standard handrails on the open side of the industrial stairs.
Recent events (2)
  • — I (S) $864
  • — Z (S) $1600

1910.141 D02 II

Serious Gravity 5 1 instance 7 exposed
Issued
Feb 27, 2015
Abate by
Mar 11, 2015
Penalty
Initial $1,600 · Current $864 Reduced
29 CFR 1910.141(d)(2)(ii): Lavatories were not provided with hot and cold, or tepid running water:    (a) Bathroom - On or about December 10,2014 the bathrooms adjacent to the break room did not have hot water.
Recent events (2)
  • — I (S) $864
  • — Z (S) $1600

1910.141 D02 III

Serious Gravity 5 2 instances 7 exposed
Issued
Feb 27, 2015
Abate by
Mar 11, 2015
Penalty
Initial $0 · Current $0
29 CFR 1910.141(d)(2)(iii): Lavatories were not provided with hand soap or similar cleansing agent:  (a) Bathroom - On or about December 10, 2014 the bathrooms adjacent to the break room did not have soap or any cleaning agent in them
Recent events (2)
  • — I (S) $0
  • — Z (S) $0

1910.141 D02 IV

Serious Gravity 5 1 instance 7 exposed
Issued
Feb 27, 2015
Abate by
Mar 11, 2015
Penalty
Initial $0 · Current $0
29 CFR 1910.141(d)(2)(iv): Lavatories were not provided with individual hand towels or sections thereof, of cloth or paper, warm air blowers or clean individual sections of continuous cloth toweling:  (a) Bathroom - On or about December 10, 2014 the bathrooms adjacent to the break room did not have hand towels or cloth or paper towels.
Recent events (2)
  • — I (S) $0
  • — Z (S) $0

1910.147 C01

Serious Gravity 10 1 instance 2 exposed
Issued
Feb 27, 2015
Abate by
Mar 30, 2015
Penalty
Initial $2,800 · Current $1,512 Reduced
29 CFR 1910.147(c)(1): The employer did not establish a program consisting of an energy control procedure, employee training and periodic inspections to ensure that before any employee performed any servicing or maintenance on a machine or equipment where the unexpected energizing, startup or release of stored energy could occur and cause injury, the machine or equipment shall be isolated from the energy source and rendered inoperative:    (a) Woodworking Area - On or about December 10, 2014 the employer had not established or implemented a written lockout/tagout program for employees servicing or performing maintenance on equipment such as, but not limited to, chippers, gang rip saws and other saws.
Recent events (2)
  • — I (S) $1512
  • — Z (S) $2800

1910.1200 E01

Serious Gravity 1 1 instance 3 exposed
Issued
Feb 27, 2015
Abate by
Mar 23, 2015
Penalty
Initial $1,200 · Current $680 Reduced
29 CFR 1910.1200(e)(1): The employer did not develop, implement, and/or maintain at the workplace a written hazard communication program which describes how the criteria specified in 29 CFR 1910.1200(f), (g), and (h) will be met:    (a) Woodworking Area - On or about December 10, 2014 the employer has not established or implemented a written Hazard Communication program for employees using hazardous materials such as, but not limited to, gasoline, paints and hydraulic oil.
Recent events (2)
  • — I (S) $680
  • — Z (S) $1200

1910.22 A01

Other-than-serious 1 instance 7 exposed
Issued
Feb 27, 2015
Abate by
Mar 11, 2015
Penalty
Initial $0 · Current $0
29 CFR 1910.22(a)(1): All places of employment, passageways, storerooms or service rooms were not kept clean and orderly or in a sanitary condition.  (a) Break Room - On or about December 10, 2014 the break room was not clean, orderly and kept in a sanitary condition.
Recent events (2)
  • — I (O) $0
  • — Z (O) $0

1910.303 G01

Other-than-serious 1 instance 7 exposed
Issued
Feb 27, 2015
Abate by
Mar 11, 2015
Penalty
Initial $0 · Current $0
29 CFR 1910.303(g)(1): Sufficient access and working space was not provided and maintained about all electric equipment (operating at 600 volts, nominal, or less to ground) to permit ready and safe operation and maintenance of such equipment:  (a) Woodworking Area - On or about December 10, 2014, access to the main electrical disconnect was blocked by wood and other objects.
Recent events (2)
  • — I (O) $0
  • — Z (O) $0

View Kenco, INC's full OSHA safety record →

This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 340139583.

Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.