RICHMOND HILL, GA —
OSHA Inspection: TIM TURNER
Planned inspection · Safety discipline
At a glance
On , OSHA opened a planned safety inspection of TIM TURNER in 466 SUNBURY DRIVE LOT # 206, RICHMOND HILL, GA 31324 (NAICS 238170). OSHA activity number 340444389.
OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- TIM TURNER
- Site address
- 466 SUNBURY DRIVE LOT # 206
- City
- RICHMOND HILL
- State
- GA
- ZIP
- 31324
- Mailing
- 276 RICHARD BLOCKER ROAD, GLENNVILLE, GA 30427
What kind of inspection was it?
- Inspection type
- Planned (H)
- Scope
- Partial (B)
- Discipline
- Safety
- Advance notice
- No
- Union status
- B
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 238170
- Employees
- 3
- Ownership type
- A
Citations
3 citations on file for this inspection.
1926.501 B13
- Issued
- Mar 12, 2015
- Abate by
- Apr 7, 2015
- Penalty
- Initial $1,600 · Current $1,200 Reduced
General-duty citation text
29 CFR 1926.501(b)(13): Each employee(s) engaged in residential construction activities 6 feet (1.8 m) or more above lower levels were not protected by guardrail systems, safety net system, or personal fall arrest system, nor were employee(s) provided with an alternative fall protection measure under another provision of paragraph 1926.501(b). a). Garage and Porch Overhangs - On or about and times prior to March 5, 2015, employees were installing vinyl siding while working from the garage and porch overhangs without any fall protection system in place, thus exposing employees to a fall hazard of 10.15 feet to earthen ground.
Recent events (2)
- — I (S) $1200
- — Z (S) $1600
1926.503 A01
- Issued
- Mar 12, 2015
- Abate by
- Apr 7, 2015
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1926.503(a)(1): The employer did not provide a training program for each employee potentially exposed to fall hazards to enable each employee to recognize the hazards of falling and the procedures to be followed in order to minimize these hazards. a). Garage and Porch Overhangs - On or about and times prior to March 5, 2015, the employer did not provide fall protection training to employees installing vinyl siding while working from garage and porch overhangs, thus exposing employees to a fall hazard of 10.15 feet to earthen ground.
Recent events (2)
- — I (S) $0
- — Z (S) $0
1926.102 A01
- Issued
- Mar 12, 2015
- Abate by
- Apr 7, 2015
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1926.102(a)(1): Eye and face protective equipment were not used when machines or operations presented potential eye or face injury from physical, chemical, or radiation agents. a). Garage and Porch Overhangs - On or about March 5, 2015 an employee was using a manually powered hammer to install vinyl siding without eye protection, thus exposing the employee to eye injuries.
Recent events (2)
- — I (O) $0
- — Z (O) $0
More inspections at TIM Turner
View TIM Turner's full OSHA safety record →
More inspections in this industry (NAICS 238170)
More inspections in GA
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 340444389.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.