OSHA Inspection: RENAISSANCE MOVING & STORAGE, INC., AND LIVINGSTON MOVING & STORAGE, INC., AN INTEGRATED ENTERPRISE

Issued

May 22, 2015

Abate by

Jul 10, 2015

Penalty

Initial $2,800 · Current $0 Reduced

General-duty citation text

29 CFR 1910.23(a)(8): Every floor hole into which persons can accidentally walk were not guarded:  a) Parking lot, on or about 3/31/2015: Employees walking through the parking lot were exposed to a trip hazard due to a missing drainage grate.

Issued

May 22, 2015

Abate by

Jun 4, 2015

Penalty

Initial $2,800 · Current $0 Reduced

General-duty citation text

29 CFR 1910.36(d)(1): Employee(s) were not able to open an exit route door from the inside at all times without keys, tools, or special knowledge:  a) Back Door of P1 Building, on or about 3/31/2015: Emergency exit door was not able to be opened from the inside, exposing employees to a fire hazard.

Issued

May 22, 2015

Abate by

Jun 4, 2015

Penalty

Initial $2,800 · Current $0 Reduced

General-duty citation text

29 CFR 1910.215(a)(4): Work rest(s) on grinding machinery were not adjusted closely to the wheel with a maximum opening of one eighth inch:  a) Maintenance Shop, on or about 3/31/2015: Employee operated a Delta 6" Bench Grinder with the abrasive wheel work rest not adjusted to 1/8 of an inch, exposing employee to a struck by hazard.

Issued

May 22, 2015

Abate by

Jun 4, 2015

Penalty

Initial $0 · Current $0

General-duty citation text

29 CFR 1910.215(b)(9): The distance between the abrasive wheel periphery(s) and the adjustable tongue or the end of the safety guard peripheral member at the top exceeded one fourth inch:  a) Maintenance Shop, on or about 3/31/2015: Employee operated a Delta 6" Bench Grinder with the abrasive wheel tongue guard was not adjusted to 1/4 of an inch, exposing employee to a struck by hazard.

Issued

May 22, 2015

Abate by

Jun 4, 2015

Penalty

Initial $2,800 · Current $0 Reduced

General-duty citation text

29 CFR 1910.253(b)(2)(iv): Valve protection caps, where cylinders were designed to accept caps, were not always in place, hand-tight, except when cylinders were in use or connected for use:  a) Maintenance Shop, on or about 3/31/2015: Acetylene and Oxygen tanks were stored in a kart with regulators connected and not separated by a fire wall, employee was exposed to a fire hazard.

Issued

May 22, 2015

Abate by

Jul 10, 2015

Penalty

Initial $2,800 · Current $0 Reduced

General-duty citation text

29 CFR 1910.303(f)(2): Each service, feeder, and branch circuit, at its disconnecting means or overcurrent device, was not legibly marked to indicate its purpose, nor located and arranged so the purpose was evident:  a) Maintenance Shop, on or about 3/31/2015: Challenge Electrical Distribution Panel was not label identifying to which equipment each circuit overcurrent device belongs, exposing employees to a fire hazard.

Issued

May 22, 2015

Abate by

Jul 10, 2015

Penalty

Initial $0 · Current $0

General-duty citation text

29 CFR 1910.303(g)(1)(i)(A): For electric equipment operating at 600 volts, nominal, or less to ground, and likely to require examination, adjustment, servicing, or maintenance while energized, the depth of the working space in the direction of access to live parts (as measured from the live parts where they were exposed or from the enclosure front or opening whwere they were enclosed) was less than indicated in Table S-1 of Subpart S of Part 1910:  a) Maintenance Shop, on or about 3/31/2015: Challenger Electrical Distribution Panel was blocked by an Ingersoll Rand 80 gallon air compressor, employees were exposed to a fire hazard.