OSHA Inspection: WAVERLY ENTERTAINMENT INC.

Issued

Dec 10, 2015

Abate by

Dec 22, 2015

Penalty

Initial $4,200 · Current $2,520 Reduced

General-duty citation text

29 CFR 1910.22(a)(1): All places of employment, passageways, storerooms or service rooms were not kept clean and orderly or in a sanitary condition:    (a) Big Dipper Area:  On or about June 25, 2015, and times prior, the floor, ground, and equipment in the mechanical area where employees are working daily performing maintenance activities was not kept clear of grease and oil.      (b) Office Area:  On or about June 25, 2015, and times prior, the administrative office area where employees work daily was not kept clear of material and debris such as paint cans, cleaning materials, miscellaneous office products, and boxes.    (c) Maintenance Shop:  On or about June 25, 2015, and times prior, the floors, tables, equipment, and storage shelving in the shop area were not kept clear of material and debris, such as, metal shavings and other debris around the American Tool Works Company lathe.        ABATEMENT CERTIFICATION IS REQUIRED FOR THIS ITEM

Issued

Dec 10, 2015

Abate by

Dec 22, 2015

Penalty

Initial $0 · Current $0

General-duty citation text

29 CFR 1910.37(a)(3): Exit route(s) were not kept free and unobstructed:  (a) Administrative offices:  On or about June 25, 2015, and times prior, the exit route was obstructed by boxes, paint cans, cleaning materials, and other miscellaneous office equipment and supplies.  (b) Maintenance Shop:  On or about June 25, 2015, and times prior, the only designated exit route was obstructed by trash cans, paint cans, shop equipment, and other miscellaneous shop supplies.     (c) Log Plume:  On or about June 25, 2015, and times prior, a plastic pipe measuring 1 foot off the ground obstructs the exit path.      ABATEMENT CERTIFICATION IS REQUIRED FOR THIS ITEM

Issued

Dec 10, 2015

Abate by

Dec 22, 2015

Penalty

Initial $0 · Current $0

General-duty citation text

29 CFR 1910.37(b)(2): Each exit was not clearly visible and marked by a sign reading "Exit":  (a)Maintenance Shop:  On or about June 25, 2015, and times prior, the only designated exit was not identified or marked with an exit sign.    ABATEMENT CERTIFICATION IS REQUIRED FOR THIS ITEM

Issued

Dec 10, 2015

Abate by

Dec 22, 2015

Penalty

Initial $4,200 · Current $2,520 Reduced

General-duty citation text

29 CFR 1910.23(a)(9): Every floor hole into which persons could accidentally walk was not protected by a cover that leaves no openings more than 1 inch wide:    (a) Log Flume:  On or about June 25, 2015, and times prior, employees were working on a platform approximately 30 feet to the ground that had uncovered holes that were approximately 9 inches in width and 5 foot in length between each handrail.    (b)  Log Flume:  On or about June 25, 2015, and times prior, employees walk up a walkway to access the operator platform at the top, between the handrail and the ride there are uncovered holes that are 9 inches wide by 5 foot in length all the way to the top of the ride.          ABATEMENT CERTIFICATION IS REQUIRED FOR THIS ITEM

Issued

Dec 10, 2015

Abate by

Jan 7, 2016

Penalty

Initial $4,900 · Current $2,940 Reduced

General-duty citation text

29 CFR 1910.23(c)(2): Runways four feet or more above floor or ground level were not guarded by standard railings (or the equivalent) and toeboards:    (a) Big Dipper:  On or about June 25, 2015, and times prior, the runway located at the start of the ride and used by employees to perform maintenance activities, measuring 4 foot 6 inches to the ground has a wire intermediate rail that does not have enough tension to reduce the visible sag and has a 2 foot 7 inches wide by 5 foot long opening between the runway walking surface and railing.       (b) Big Dipper:  On or about June 25, 2015, and times prior, the runway located at the highest point of the ride and used by employees to perform maintenance activities, measuring approximately 40 foot to ground has a wire intermediate rail that is sagging to the runway floor and has a visible opening from ground level between the runway walking surface and the railing.    (c) Big Dipper:  On or about June 25, 2015, and times prior, the runway located at the end of the ride and used by employees to perform maintenance activities, measuring 6 foot 8 inches to the ground is missing an intermediate rail and has a 2 foot 2 inch wide by 5 foot long opening between the railing and the walking surface of the runway.       (d) Little Dipper:  On or about June 25, 2015, and times prior, the runway around the outer perimeter of the ride is used by employees to perform maintenance activities, measuring approximately 20 foot to the ground at the highest point has a chain top rail that does not have enough tension to reduce the visible sag and is missing an intermediate rail.        ABATEMENT DOCUMENTATION IS REQUIRED FOR THIS ITEM

Issued

Dec 10, 2015

Abate by

Dec 22, 2015

Penalty

Initial $0 · Current $0

General-duty citation text

29 CFR 1910.23(c)(3): Regardless of height, open-sided floors, walkways, platforms, or runways above or adjacent to dangerous equipment, pickling or galvanizing tanks, degreasing units, and similar hazards were not guarded with a standard railing and toe board:  (a) Log Flume:  On or about June 25, 2015, and times prior, a walkway that crosses over moving water, leading to approximately 10 foot of water with a rotating blade, that is used to gain access to the work platform has one open side that did not have a handrail and one side missing an intermediate rail.   ABATEMENT DOCUMENTATION IS REQUIRED FOR THIS ITEM

Issued

Dec 10, 2015

Abate by

Dec 30, 2015

Penalty

Initial $3,500 · Current $2,100 Reduced

General-duty citation text

29 CFR 1910.23(d)(1): Every flight of stairs having four or more risers shall be equipped with standard stair railings or standard handrails as specified in paragraphs (d)(1)(i) through (v) of this section:    (a) Big Dipper, starting side:  On or about June 25, 2015, and times prior, ride operators and maintenance employees use the stairs, measuring 3 foot 7 inches from platform to ground with 5 risers that was not equipped with an intermediate railing.      (b) Big Dipper, end near operator station:  On or about June 25, 2015, and times prior, ride operators and maintenance employees use the stairs, measuring 5 foot 4 inches from platform to ground with 8 risers that was not equipped with an intermediate railing.        ABATEMENT CERTIFICATION IS REQUIRED FOR THIS ITEM

Issued

Dec 10, 2015

Abate by

Jan 7, 2016

Penalty

Initial $4,900 · Current $2,940 Reduced

General-duty citation text

29 CFR 1910.147(c)(1): The employer did not establish a program consisting of an energy control procedure, employee training and periodic inspections to ensure that before any employee performed any servicing or maintenance on a machine or equipment where the unexpected energizing, startup or release of stored energy could occur and cause injury, the machine or equipment shall be isolated from the energy source and rendered inoperative.    (a) Camden Park:  On or about June 25, 2015, and times prior, an energy control program was not established for employees required to perform service and maintenance on amusement park rides, such as oiling and greasing the chain, fittings, and track without isolating the pneumatic, electric, and gravity energy sources.        ABATEMENT DOCUMENTATION IS REQUIRED FOR THIS ITEM

Issued

Dec 10, 2015

Abate by

Dec 22, 2015

Penalty

Initial $4,200 · Current $2,520 Reduced

General-duty citation text

29 CFR 1910.212(a)(1): One or more methods of machine guarding was not provided to protect the operator and other employees in the machine area from hazards such as those created by point of operation, ingoing nip points, rotating parts, flying chips and sparks:    (a) Maintenance Shop:  On or about June 25, 2015, and times prior, the Round Tower mill with a 20 inch drill press, Serial Number 8407124, used by maintenance employees to drill holes in steel was not provided with an adjustable guard to cover the unused portion of the bit and chuck above the material being worked.     (b) Maintenance Shop:  On or about June 25, 2015, and times prior, the Central Machinery 20 inch drill press, Serial Number 0504130045, used by maintenance employees to drill holes in steel was not provided with an adjustable guard to cover the unused portion of the bit and chuck above the material being worked.     (c) Maintenance Shop:  On or about June 25, 2015, and times prior, the American Tool Works Corporation lathe, used by maintenance employees was not provided with a chuck guard to protect the operators from being struck by the 12 inch rotating chuck.      (d) Maintenance Shop:  On or about June 25, 2015, and times prior, the Central Machinery horizontal/vertical bandsaw, Serial Number 358451504, used by maintenance employees to cut steel and pipe had an 8 inch section of unused blade that was not guarded.      ABATEMENT CERTIFICATION IS REQUIRED FOR ITEM

Issued

Dec 10, 2015

Penalty

Initial $0 · Current $0

General-duty citation text

29 CFR 1910.212(a)(5): Fan blade guard(s) were not provided where the periphery of the blades was than seven (7) feet above the floor or working level, the fan's blades were not guarded by a guard which had openings no larger than one-half (1/2) inch.  (a) Maintenance Shop:  On or about June 25, 2015, and times prior, employees use and work around an industrial floor fan measuring 75 inches wide by 60 inches in height that was not provided with a guard on the backside to cover the four 20 inch rotating blades.

Issued

Dec 10, 2015

Abate by

Dec 22, 2015

Penalty

Initial $0 · Current $0

General-duty citation text

29 CFR 1910.212(b): Machine(s) designed for fixed location(s) were not securely anchored to prevent walking or moving:  (a) Maintenance Shop:  On or about June 25, 2015, and times prior, the Central Machinery 20 inch drill press, Serial Number 0504130045, used by maintenance employees to drill holes in steel was not secured.     ABATEMENT CERTIFICATION IS REQUIRED FOR THIS ITEM

Issued

Dec 10, 2015

Abate by

Dec 22, 2015

Penalty

Initial $4,200 · Current $2,520 Reduced

General-duty citation text

29 CFR 1910.213(h)(1): Radial saw(s) were not provided with an upper hood that completely enclosed the upper portion of the blade down to a point including the end of the saw arbor, and the sides of the lower exposed portion of the blade were not guarded:    (a)  Maintenance Shop:  On or about June 25, 2015, and times prior, the Dewalt 10 inch radial arm saw, used by maintenance employees to cut wood material for roller coasters was not provided with a guard on the lower portion of the blade.        ABATEMENT CERTIFICATION IS REQUIRED FOR THIS ITEM

Issued

Dec 10, 2015

Abate by

Dec 22, 2015

Penalty

Initial $0 · Current $0

General-duty citation text

29 CFR 1910.213(h)(2): Radial saw(s) used for ripping were not provided with nonkickback fingers or dogs located on both sides of the saw so as to oppose the trust or tendency of the saw to pick up material or throw it back toward the operator.  (a)  Maintenance Shop:  On or about June 25, 2015, and times prior, the Dewalt 10 inch radial arm saw, used by maintenance employees to rip 4X4, 4X6, 4X12 pieces of wood was not provided with a nonkickback device.     ABATEMENT CERTIFICATION IS REQUIRED FOR THIS ITEM

Issued

Dec 10, 2015

Abate by

Dec 22, 2015

Penalty

Initial $0 · Current $0

General-duty citation text

29 CFR 1910.213(h)(3): Radial saw(s) were not provided with an adjustable stop to prevent the forward travel of the blade beyond the position necessary to complete the cut in repetitive operations.  (a)  Maintenance Shop:  On or about June 25, 2015, and times prior, the Dewalt 10 inch radial arm saw, used by maintenance employees to cut wood material for roller coasters was not provided with a stop and traveled 10 inches past the table.     ABATEMENT CERTIFICATION IS REQUIRED FOR THIS ITEM

Issued

Dec 10, 2015

Abate by

Dec 22, 2015

Penalty

Initial $0 · Current $0

General-duty citation text

29 CFR 1910.213(h)(4): Radial saw(s) were not installed in a manner so as to cause the cutting head to return gently to the starting position when released by the operator.  (a)  Maintenance Shop:  On or about June 25, 2015, and times prior, the Dewalt 10 inch radial arm saw, used by maintenance employees to cut wood material for roller coasters does not return to the starting position when released.     ABATEMENT CERTIFICATION IS REQUIRED FOR THIS ITEM

Issued

Dec 10, 2015

Abate by

Dec 18, 2015

Penalty

Initial $2,100 · Current $1,260 Reduced

General-duty citation text

29 CFR 1910.215(a)(4): Work rest(s) on grinding machinery were not adjusted closely to the wheel with a maximum opening of one eighth inch:    (a) Maintenance Shop:  On or about June 25, 2015, and times prior, the 2012 6 inch Dewalt bench grinder, Serial Number 45-YL78376, used by maintenance employees to grind down and make parts for the rides had a work rest opening of a 1/2 inch on both sides.      ABATEMENT CERTIFICATION IS REQUIRED FOR THIS ITEM

Issued

Dec 10, 2015

Abate by

Dec 18, 2015

Penalty

Initial $0 · Current $0

General-duty citation text

29 CFR 1910.215(b)(9): The distance between the abrasive wheel periphery(s) and the adjustable tongue or the end of the safety guard peripheral member at the top exceeded one fourth inch.  (a) Maintenance Shop:  On or about June 25, 2015, and times prior, the 2012 6 inch Dewalt bench grinder, Serial Number 45-YL78376, used by maintenance employees to grind down and make parts for the rides had tongue guard openings of a 1/2 inch on left abrasive wheel and 3/8 inch on the right abrasive wheel.   ABATEMENT CERTIFICATION IS REQUIRED FOR THIS ITEM

Issued

Dec 10, 2015

Abate by

Dec 22, 2015

Penalty

Initial $4,200 · Current $2,520 Reduced

General-duty citation text

29 CFR 1910.219(d)(1): Pulley(s) with part(s) seven feet or less from the floor or work platform were not guarded in accordance with the requirements specified in 29 CFR 1910.219(m) and (o):    (a) Maintenance Shop:  On or about June 25, 2015, and times prior, employees use and work around an industrial floor fan measuring 75 inches wide by 60 inches in height that was not provided with a guard on the backside to cover the pulley that was 21 inches from the floor.    (b) Maintenance Shop:  On or about June 25, 2015, and times prior, employees use and work around a compressor that was not provided with a guard to cover the pulley that was 25 inches from the floor.     (c) Big Dipper:  On or about June 25, 2015, and times prior, maintenance employees work in the control area where a guard was not provided to cover the pulley that was 24 inches from the ground.        ABATEMENT CERTIFICATION REQUIRED FOR THIS ITEM

Issued

Dec 10, 2015

Abate by

Dec 22, 2015

Penalty

Initial $0 · Current $0

General-duty citation text

29 CFR 1910.219(f)(3): Sprocket wheels and chains that were seven (7) or less feet from the floor or platform were not enclosed:  (a) Big Dipper: On or about June 25, 2015, and times prior, employees work near and around the chain powered by 440V, 3 phase electric power that is not provided with a guard on the top of the trough or in the control area where the chain is less than 7 feet from the floor and unprotected on all sides.    (b) Little Dipper:  On or about June 25, 2015, and times prior, employees work near and around the chain powered by 240V, 3 phase electric power is not provided with a guard on the top of the trough.   ABATEMENT CERTIFICATION IS REQUIRED FOR THIS ITEM

Issued

Dec 10, 2015

Abate by

Dec 22, 2015

Penalty

Initial $0 · Current $0

General-duty citation text

29 CFR 1910.219(f)(4): For gears, sprockets and chains that need frequent oiling, openings with hinged or sliding self-closing covers were not provided. All points not readily accessible did not have oil feed tubes for lubricant to be added while machinery was in motion:  (a) Big Dipper: On or about June 25, 2015, and times prior, maintenance employees are required to oil the chain powered by 440V, 3 phase electric power daily that is not provided with a cover or oil feed tubes.   (b) Little Dipper:  On or about June 25, 2015, and times prior, maintenance employees are required to oil the chain powered by 240V, 3 phase electric power daily that is not provided with a cover or oil feed tubes.    ABATEMENT CERTIFICATION IS REQUIRED FOR THIS ITEM

Issued

Dec 10, 2015

Abate by

Jan 7, 2016

Penalty

Initial $2,800 · Current $1,680 Reduced

General-duty citation text

29 CFR 1910.253(e)(3)(ii)(C)(3): Flashback protection was not provided by an approved device that would prevent flame from passing into the fuel gas system:    (a) Maintenance Shop:  On or about June 25, 2015, and times prior, oxygen and acetylene burning torches used by employees were not provided with flash back arrestors.       ABATEMENT CERTIFICATION IS REQUIRED FOR THIS ITEM

Issued

Dec 10, 2015

Abate by

Jan 7, 2016

Penalty

Initial $0 · Current $0

General-duty citation text

29 CFR 1910.253(e)(5)(iv): Hose connections were not clamped or otherwise securely fastened in a manner that would withstand, without leakage, twice the pressure to which they would normally be subjected in service, but in no case less than a pressure of 300 psi.  (a) Maintenance Shop:  On or about June 25, 2015, and times prior, employees use burning hoses that were not pressure tested to at least 300 psi after repairs were made.     ABATEMENT CERTIFICATION IS REQUIRED FOR THIS ITEM

Issued

Dec 10, 2015

Penalty

Initial $2,800 · Current $1,680 Reduced

General-duty citation text

29 CFR 1910.254(b)(4)(iv): Terminals for welding leads were not protected from accidental contact by personnel or metal objects.      (a) Maintenance Shop:  On or about June 25, 2015, and times prior, the 240V-460V Lincoln Arch Welder, Model 250, Serial Number AC-544000, used by maintenance employees has terminals for welding leads that were not protected.

Issued

Dec 10, 2015

Penalty

Initial $0 · Current $0

General-duty citation text

29 CFR 1910.254(d)(8): Welding cables with splices within 10 feet (3 m) of the holder were used.  (a) Maintenance Shop:  On or about June 25, 2015, and times prior, the 240V-460V Lincoln Arch Welder, Model 250, Serial Number AC-544000, used by maintenance employees had a repair that was 2 feet from the holder.

Issued

Dec 10, 2015

Penalty

Initial $0 · Current $0

General-duty citation text

29 CFR 1910.254(d)(9)(iii): Cables with damaged insulation or exposed bare conductors were not replaced.  (a) Maintenance Shop:  On or about June 25, 2015, and times prior, the cables on the 240V-460V Lincoln Arch Welder, Model 250, Serial Number AC-544000, used by maintenance employees had damaged insulation and exposed conductors.

Issued

Dec 10, 2015

Abate by

Dec 22, 2015

Penalty

Initial $2,800 · Current $1,680 Reduced

General-duty citation text

29 CFR 1910.303(b)(1): Electrical equipment was not free from recognized hazards that were likely to cause death or serious physical harm to employees:    (a) Maintenance Shop: On or about June 25, 2015, and times prior, the extension cord used to power shop equipment and hand tools was missing a section of outer insulation exposing the insulated conductors.      (b) West Virginia Grille: On or about June 25, 2015, and times prior, the electric wires that power the overhead lights in the restroom was missing the outer insulation exposing the insulated conductors.      ABATEMENT CERTIFICATION IS REQUIRED FOR THIS ITEM

Issued

Dec 10, 2015

Abate by

Dec 22, 2015

Penalty

Initial $0 · Current $0

General-duty citation text

29 CFR 1910.303(b)(7): Electric equipment was not installed in a neat and workmanlike manner:  (a) West Virginia Grille: On or about June 25, 2015, and times prior, the romex cable and electrical wiring that powers the overhead lights in the restroom was not properly secured and the wire connections and caps were exposed.    ABATEMENT CERTIFICATION IS REQUIRED FOR THIS ITEM

Issued

Dec 10, 2015

Penalty

Initial $0 · Current $0

General-duty citation text

29 CFR 1910.304(g)(5): The path to ground from circuits, equipment, and enclosures was not permanent, continuous, and effective:  (a) Maintenance Shop: On or about June 25, 2015, and times prior, employees use an extension cord to power shop equipment that was missing the ground plug.   (b) Maintenance Shop: On or about June 25, 2015, and times prior, the power plug for the 240V-460V Lincoln Arch Welder, Model 250, Serial Number AC-544000, used by maintenance employees had a damaged ground plug that had an exposed bare conductor.

Issued

Dec 10, 2015

Abate by

Dec 30, 2015

Penalty

Initial $2,100 · Current $1,260 Reduced

General-duty citation text

29 CFR 1910.303(e): Markings were not provided on electrical equipment giving voltage, current, wattage, and other ratings as necessary.    (a) Big Dipper:  On or about June 25, 2015, and times prior, the panel that contained the 440 volt 3 phase Allen and Bradley 709 starter was not marked or labeled.        ABATEMENT CERTIFICATION IS REQUIRED FOR THIS ITEM

Issued

Dec 10, 2015

Abate by

Dec 30, 2015

Penalty

Initial $0 · Current $0

General-duty citation text

29 CFR 1910.303(f)(1): Each disconnecting means required by Subpart S of Part 1910 for motors and appliances was not legibly marked to indicate its purpose, nor located and arranged so the purpose was evident.  (a) Big Dipper:  On or about June 25, 2015, and times prior, the main disconnect for the 440 volt 3 phase Allen and Bradley 709 starter was not marked or labeled.    (b) Big Dipper:  On or about June 25, 2015, and times prior, the on/off switch located at the operator stand was wired to a light switch that was not marked indicating the purpose.    (c) Throughout Park:  On or about June 25, 2015, and times prior, buildings containing disconnects for the Rattler, Paratrooper, and Log Flume were not marked indicating their purpose.   ABATEMENT CERTIFICATION IS REQUIRED FOR THIS ITEM

Issued

Dec 10, 2015

Abate by

Dec 30, 2015

Penalty

Initial $0 · Current $0

General-duty citation text

29 CFR 1910.303(f)(2): Each service, feeder, and branch circuit, at its disconnecting means or overcurrent device, was not legibly marked to indicate its purpose, nor located and arranged so the purpose was evident.  (a) Maintenance Shop:  On or about June 25, 2015, and times prior, two electrical panels that contain the circuit breakers used to power shop equipment, such as, but not limited to the Round Tower mill, Central Machinery 20 inch drill press, and  American Tool Works Corporation lathe were not labeled indicating the purpose.     ABATEMENT CERTIFICATION IS REQUIRED FOR THIS ITEM

Issued

Dec 10, 2015

Abate by

Dec 30, 2015

Penalty

Initial $2,100 · Current $1,260 Reduced

General-duty citation text

29 CFR 1910.303(g)(2)(ii): In locations where electric equipment was likely to be exposed to physical damage, enclosures or guards were not so arranged and of such strength as to prevent such damage:    (a) West Virginia Grille:  On or about June 25, 2015, and times prior, employees are required to move stock to and from shelving exposing the unprotected fluorescent lights to damage.       ABATEMENT CERTIFICATON IS REQUIRED FOR THIS ITEM

Issued

Dec 10, 2015

Abate by

Jan 7, 2016

Penalty

Initial $4,900 · Current $2,940 Reduced

General-duty citation text

29 CFR 1910.333(a): Safety-related work practices were not employed to prevent electric shock or other injuries resulting from either direct or indirect electrical contacts, when work was performed near or on equipment or circuits which were or could be energized:    (a) Camden Park:  On or about June 25, 2015, and times prior, electrical safety work practices were not established for employees required to work on electrical equipment for the amusement park rides, such as replacing the 440 volt 3 phase main contact switch for the Big Dipper, replace safety switches for the Rattler, and repairing parts in components of the control panels for the Paratrooper and Bullseye.          ABATEMENT DOCUMENTATION IS REQUIRED FOR THIS ITEM

Issued

Dec 10, 2015

Abate by

Jan 7, 2016

Penalty

Initial $2,800 · Current $1,680 Reduced

General-duty citation text

29 CFR 1910.1030(c)(1)(i): The employer having employee(s) with occupational exposure did not establish a written Exposure Control Plan designed to eliminate or minimize employee exposure:    (a) Huntington: On or about June 25, 2015, and times prior, an employee was observed providing first aid to a customer without an established written Exposure Control Plan.      ABATMENT CERTIFICATIN IS REQUIRED FOR THIS ITEM

Issued

Dec 10, 2015

Abate by

Jan 7, 2016

Penalty

Initial $0 · Current $0

General-duty citation text

29 CFR 1910.1030(g)(2)(i): The employer did not ensure that each employee with occupational exposure participated in a training program.  (a) Huntington: On or about June 25, 2015, and times prior, an employee was observed providing first aid to a customer and did not participate in a training program.   ABATEMENT CERTIFICATION IS REQUIRED FOR THIS ITEM

Issued

Dec 10, 2015

Abate by

Jan 7, 2016

Penalty

Initial $3,500 · Current $2,100 Reduced

General-duty citation text

29 CFR 1910.1200(e)(1): Employer had not developed or implemented a written hazard communication program including the requirements outlined in 29 CFR 1910.1200(e)(1)(i) and (e)(1)(ii):     (a) Camden Park:  On or about June 25, 2015, and times prior, a written hazard communication program has not been developed for employees that use and are exposed to hazardous chemicals including, but not limited to, hydraulic fluid, iron oxide from welding fumes, red and tacky grease, marine grease, and household bleach.      ABATEMENT CERTIFICATION IS REQUIRED FOR THIS ITEM

Issued

Dec 10, 2015

Abate by

Jan 7, 2016

Penalty

Initial $0 · Current $0

General-duty citation text

29 CFR 1910.1200(g)(8):   The employer did not maintain in the workplace copies of the required safety data sheets for each hazardous chemical, and did not ensure that they were readily accessible during each work  shift to employees when they were in their work area(s).  (a) Camden Park:  On or about June 25, 2015, and times prior, safety data sheets for each hazardous chemical, including hydraulic fluid, iron oxide from welding fumes, red and tacky grease, marine grease, and household bleach, were not available to employees.   ABATEMENT CERTIFICATION IS REQUIRED FOR THIS ITEM

Issued

Dec 10, 2015

Abate by

Jan 7, 2016

Penalty

Initial $0 · Current $0

General-duty citation text

29 CFR 1910.1200(h)(1): Employees were not provided effective information and training on hazardous chemicals in their work area at the time of their initial assignment and whenever a new hazard that the employees had not been previously trained about was introduced into their work area:  (a) Camden Park:  On or about June 25, 2015, and times prior, employees had not received training on hazardous materials that are used in the work area, such as, hydraulic fluids, greases, paints, thinners, and cleaning products.      ABATEMENT CERTIFICATION IS REQUIRED FOR THIS ITEM

Issued

Dec 10, 2015

Abate by

Dec 22, 2015

Penalty

Initial $4,200 · Current $2,520 Reduced

General-duty citation text

29 CFR 1910.157(c)(1): Portable fire extinguishers were not mounted, located and identified so that they were readily accessible without subjecting the employees to injuries:     (a) Maintenance Shop:  On or about June 25, 2015, and times prior, a ABC Dry Chemical portable fire extinguisher located behind a locker on the wall was not identified or accessible.        ABATEMENT CERTIFICATION IS REQUIRED FOR THIS ITEM

Issued

Dec 10, 2015

Abate by

Jan 7, 2016

Penalty

Initial $0 · Current $0

General-duty citation text

29 CFR 1910.157(g)(1): An educational program was not provided for all employees to familiarize them with the general principles of fire extinguisher use and the hazards involved with incipient stage firefighting.  (a) Maintenance Shop:  On or about June 25, 2015, and times prior, employees required by the employer to use fire extinguishers, had not received training.     ABATEMENT CERTIFICATION IS REQUIRED FOR THIS ITEM

Issued

Dec 10, 2015

Abate by

Dec 22, 2015

Penalty

Initial $700 · Current $420 Reduced

General-duty citation text

29 CFR 1904.29(a): A log of all Work-Related Injuries and Illnesses (OSHA Form 300), and/or the Summary of Work-Related Injuries and Illnesses, (OSHA Form 300-A) and/or the Injury and Illness Incident Report (OSHA Form 301) or equivalent forms were not kept by the establishment:    (a)  Office Area:  On or about June 25, 2015, and times prior, the OSHA Form 300 or equivalent was not used to record occupational injuries and illnesses that occur in the workplace, such as a recordable injury that occurred on June 20, 2015 resulting in 1 week of missed work that was not recorded.        ABATEMENT CERTIFICATION IS REQUIRED FOR THIS ITEM

Issued

Dec 10, 2015

Abate by

Dec 30, 2015

Penalty

Initial $0 · Current $0

General-duty citation text

29 CFR 1910.132(d)(1): The employer did not assess the workplace to determine if hazards are present, or are likely to be present, which necessitate the use of personal protective equipment (PPE):  (a) Camden Park:  On or about June 25, 2015, and times prior, employees operating shop equipment, such as drill presses, a lathe, bench grinder, and handling lubricants were not required to wear personal protective equipment.      ABATEMENT CERTIFICATION IS REQUIRED FOR THIS ITEM

Issued

Dec 10, 2015

Abate by

Dec 22, 2015

Penalty

Initial $0 · Current $0

General-duty citation text

29 CFR 1910.157(e)(2): Portable fire extinguishers were not visually inspected at least monthly.  (a) Maintenance Shop:  On or about June 25, 2015, and times prior, an ABC Dry Chemical portable fire extinguisher was not visually inspected at least monthly.     ABATEMENT CERTIFICATION IS REQUIRED FOR THIS ITEM

Issued

Dec 10, 2015

Abate by

Dec 22, 2015

Penalty

Initial $0 · Current $0

General-duty citation text

29 CFR 1910.157(e)(3): Portable fire extinguishers were not subjected to an annual maintenance check.  (a) Maintenance Shop:  On or about June 25, 2015, and times prior, a ABC Dry Chemical portable fire extinguisher was not subjected to an annual maintenance check.    ABATEMENT CERTIFICATION IS REQUIRED FOR THIS ITEM

Issued

Dec 10, 2015

Abate by

Dec 30, 2015

Penalty

Initial $0 · Current $0

General-duty citation text

29 CFR 1910.305(e)(1): Cabinets, cutout boxes, fittings, boxes, and panelboard enclosures in damp or wet locations were not installed to prevent moisture or water from entering and accumulating within the enclosures:  (a) Log Flume: On or about June 25, 2015, and times prior, a hole in the side of the electrical panel box, allowed water to enter the box.     ABATEMENT CERTIFICATION IS REQUIRED FOR THIS ITEM