LAKE CHARLES, LA —
OSHA Inspection: GOLDEN NUGGET LAKE CHARLES, LLC
Complaint inspection · Safety discipline
At a glance
On , OSHA opened a complaint safety inspection of GOLDEN NUGGET LAKE CHARLES, LLC in 2550 GOLDEN NUGGET BLVD, LAKE CHARLES, LA 70601 (NAICS 721120). OSHA activity number 340791128.
OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- GOLDEN NUGGET LAKE CHARLES, LLC
- Site address
- 2550 GOLDEN NUGGET BLVD
- City
- LAKE CHARLES
- State
- LA
- ZIP
- 70601
- Mailing
- 2550 GOLDEN NUGGET BLVD, LAKE CHARLES, LA 70601
What kind of inspection was it?
- Inspection type
- Complaint (B)
- Scope
- Partial (B)
- Discipline
- Safety
- Advance notice
- No
- Union status
- B
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 721120
- Employees
- 2420
- Ownership type
- A
Citations
5 citations on file for this inspection.
1910.213 B03
- Issued
- Oct 9, 2015
- Abate by
- Oct 29, 2015
- Penalty
- Initial $5,000 · Current $1,000 Reduced
General-duty citation text
29 CFR 1910.213(b)(3): On applications where injury to the operator might result if motors were to restart after power failures, provision was not made to prevent machines from automatically restarting upon restoration of power. On or about 7/15/15 in the Carpenter shop; the employer allowed employees to use the following wood-cutting power saws without provisions to prevent the machines from automatically restarting upon restoration of electrical power: a) The Dayton 10" saw used for ripping and cross-cutting. b) The Jet Jointer c) The Dayton 14" band saw d) The Scheppach 14" band saw
Recent events (2)
- — I (O) $1000
- — Z (S) $5000
1910.213 C01
- Issued
- Oct 9, 2015
- Abate by
- Oct 22, 2015
- Penalty
- Initial $7,000 · Current $7,000
General-duty citation text
29 CFR 1910.213(c)(1): Each circular hand-fed ripsaw was not guarded by a hood which shall completely enclose that portion of the saw above the table and that portion of the saw above the material being cut. On or about 7/15/15 in the Carpenter shop; the employer allowed employees to use the Dayton 10" saw for ripping and cross-cutting wood without a guard over the blade.
Recent events (2)
- — I (O) $7000
- — Z (S) $7000
1910.213 C02
- Issued
- Oct 9, 2015
- Abate by
- Oct 20, 2015
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.213(c)(2): Each hand-fed circular ripsaw was not furnished with a spreader to prevent material from squeezing the saw or being thrown back on the operator. On or about 7/15/15 in the Carpenter shop; the employer allowed his employees to use the Dayton 10" table saw for ripping and crossing wood and the saw was not furnished with a spreader.
Recent events (2)
- — I (O) $0
- — Z (S) $0
1910.213 C03
- Issued
- Oct 9, 2015
- Abate by
- Oct 22, 2015
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.213(c)(3): Each hand-fed circular ripsaw was not provided with nonkickback fingers or dogs so located as to oppose the thrust or tendency of the saw to pick up the material or to throw it back toward the operator. On or about 7/15/15 in the carpenter shop; the employer allowed his employees to use the Dayton 10" table saw for ripping and cross-cutting wood without non-kickback fingers.
Recent events (2)
- — I (O) $0
- — Z (S) $0
1910.333 B02
- Issued
- Oct 9, 2015
- Abate by
- Oct 16, 2015
- Penalty
- Initial $4,000 · Current $1,000 Reduced
General-duty citation text
29 CFR 1910.333(b)(2): While an employee was exposed to contact with parts of fixed electric equipment or circuits which were deenergized, the circuits energizing the parts were not locked out or tagged. on or about 7/15/15 in the employee dining room; the employer allowed an employee to change the contactor in the Hobart 480 Volt dishwasher, Model CLCS 76E, Serial #8511087624 and the employee was not provided with a lock to lockout the circuit.
Recent events (2)
- — I (O) $1000
- — Z (S) $4000
More inspections in this industry (NAICS 721120)
More inspections in LA
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 340791128.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.