ARLINGTON, TX ·
OSHA Inspection: MANUEL MORENO
Planned inspection · Safety discipline
At a glance
On , OSHA opened a planned safety inspection of MANUEL MORENO in 4211 ASPEN GROVE, ARLINGTON, TX 76011 (NAICS 238160). OSHA activity number 340979608.
OSHA opens inspections for many reasons: routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- MANUEL MORENO
- Site address
- 4211 ASPEN GROVE
- City
- ARLINGTON
- State
- TX
- ZIP
- 76011
- Mailing
- 3130 LOMBARDY LANE # 1090, DALLAS, TX 75220
What kind of inspection was it?
- Inspection type
- Planned (H)
- Scope
- Partial (B)
- Discipline
- Safety
- Advance notice
- No
- Union status
- Non-union (B)
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 238160
- Employees
- 3
- Ownership type
- Private (A)
Citations
4 citations on file for this inspection.
1926.102 A01
- Issued
- Nov 13, 2015
- Abate by
- Dec 14, 2015
- Penalty
- Initial $1,600 · Current $1,600
General-duty citation text
29 CFR 1926.102(a)(1): Eye and face protective equipment were not used when machines or operations presented potential eye or face injury from physical, chemical, or radiation agents. At the jobsite, employees operating Hitachi nail guns while performing framing activities were not wearing eye protection, exposing employees to the hazard of being struck by flying objects.
Recent events (1)
- · Z (S) $1600
1926.307 D01
- Issued
- Nov 13, 2015
- Abate by
- Dec 14, 2015
- Penalty
- Initial $2,400 · Current $2,400
General-duty citation text
29 CFR 1926.307(d)(1): Pulley(s) with part(s) seven feet (2.128 m) or less from the floor or work platform were not guarded in accordance with the requirements specified in paragraphs (m) and (o) of this section: At the jobsite, no guards were provided over the 5" and 10" pulleys to the Eaton Compressor, exposing employees to the hazard of being caught in belts and pulleys.
Recent events (1)
- · Z (S) $2400
1926.307 E01 I
- Issued
- Nov 13, 2015
- Abate by
- Dec 14, 2015
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1926.307(e)(1)(i): Horizontal belts which had both runs 7 feet (2.128 m) or less from the floor level were not guarded with a guard that extended to at least 15 inches (38.1 cm) above the belt or to a standard height specified in Table O-12: At the jobsite, no guards were provided over the 1/2" horizontal belts to the Eaton Compressor, exposing employees to the hazard of being caught in belts and pulleys.
Recent events (1)
- · Z (S) $0
1926.501 B13
- Issued
- Nov 13, 2015
- Abate by
- Dec 14, 2015
- Penalty
- Initial $2,800 · Current $2,800
General-duty citation text
29 CFR 1926.501(b)(13): Each employee(s) engaged in residential construction activities 6 feet (1.8 m) or more above lower levels were not protected by guardrail systems, safety net system, or personal fall arrest system. At the jobsite, employees engaged in roofing activities at a height of over 6 feet were not protected by a fall arrest system. Employees were exposed to an unprotected fall of over 10 feet to the ground below.
Recent events (1)
- · Z (S) $2800
More inspections in this industry (NAICS 238160)
More inspections in TX
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). OSHA publishes its own view of this case as inspection number 340979608.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.