TRUSSVILLE, AL —
OSHA Inspection: E C M SERVICE, INC.
Complaint inspection · Safety discipline
At a glance
On , OSHA opened a complaint safety inspection of E C M SERVICE, INC. in 6509 AMBER HILLS ROAD, TRUSSVILLE, AL 35173 (NAICS 333911). OSHA activity number 340985100.
OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- E C M SERVICE, INC.
- Site address
- 6509 AMBER HILLS ROAD
- City
- TRUSSVILLE
- State
- AL
- ZIP
- 35173
- Mailing
- 6509 AMBER HILLS ROAD, TRUSSVILLE, AL 35173
What kind of inspection was it?
- Inspection type
- Complaint (B)
- Scope
- Partial (B)
- Discipline
- Safety
- Advance notice
- No
- Union status
- B
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 333911
- Employees
- 24
- Ownership type
- A
Citations
7 citations on file for this inspection.
1910.184 I09 III
- Issued
- Jan 29, 2016
- Penalty
- Initial $2,040 · Current $1,224 Reduced
General-duty citation text
29 CFR 1910.184(i)(9)(iii): Synthetic web sling(s) with snags, punctures, tears, or cuts were not immediately removed from service: (a) On or about 10/13/15 - Weld shop and Machine shop, employees were using defective nylon slings attached to overhead crane to lift bearings or other metal objects weighing from 80 to 100 pounds.
Recent events (2)
- — I (S) $1224
- — Z (S) $2040
1910.212 A01
- Issued
- Jan 29, 2016
- Penalty
- Initial $2,800 · Current $1,680 Reduced
General-duty citation text
29 CFR 1910.212(a)(1): One or more methods of machine guarding was not provided to protect the operator and other employees in the machine area from hazards such as those created by point of operation, ingoing nip points, rotating parts, flying chips and sparks: (a) On or about 10/13/15 - Tear Down Shop, the Do All Master horizontal band saw did not have the unused portions of the blade guarded. (b) On or about 10/13/15 - Machine Shop, the Schiess milling machine did not have the rotating table guarded. (c) On or about 10/13/15 - Machine Shop, the Summit milling & drilling machine did not have a spindle guard installed or available for use. (d) On or about 10/13/15 - Machine Shop, the Super-Progres-S.50II horizontal lathe did not have the chuck guarded.
Recent events (2)
- — I (S) $1680
- — Z (S) $2800
1910.215 B09
- Issued
- Jan 29, 2016
- Penalty
- Initial $2,040 · Current $1,224 Reduced
General-duty citation text
29 CFR 1910.215(b)(9): Guard for abrasive wheel machine where the operator stands in front of the machine was not constructed so that the peripheral protecting member could be adjusted to the constantly decreasing diameter of the wheel: (a) On or about 10/13/15 - Pump Shop, a Delta 6 inch Thin-Line table mounted abrasive wheel bench grinder did not have the adjustable tongue guard. (b) On or about 10/13/15 - Machine Shop, a Central Machinery pedestal mounted abrasive wheel bench grinder did not have the adjustable tongue guard.
Recent events (2)
- — I (S) $1224
- — Z (S) $2040
1910.215 A02
- Issued
- Jan 29, 2016
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.215(a)(2): Abrasive wheel(s) used on grinding machinery were not provided with safety guard(s) which covered the spindle end, nut, flange projections: (a) On or about 10/13/15 - Pump Shop, a Delta 6 inch Thin-Line table mounted abrasive wheel bench grinder did not have side guards. (b) On or about 10/13/15 - Machine Shop, a Central Machinery pedestal mounted abrasive wheel bench grinder did not have side guards.
Recent events (2)
- — I (S) $0
- — Z (S) $0
1910.215 A04
- Issued
- Jan 29, 2016
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.215(a)(4): Work rest(s) on grinding machinery were not adjusted closely to the wheel with a maximum opening of one eighth inch: (a) On or about 10/13/2015 - Machine Shop, a Central Machinery pedestal abrasive grinder had a work rest that was adjusted to greater than one inch.
Recent events (2)
- — I (S) $0
- — Z (S) $0
1910.303 B02
- Issued
- Jan 29, 2016
- Penalty
- Initial $2,040 · Current $1,224 Reduced
General-duty citation text
29 CFR 1910.303(b)(2): Listed or labeled electrical equipment was not used or installed in accordance with instructions included in the listing or labeling: (a) On or about 10/13/15 - Weld Shop, two air conditioner fans were placed on the floor and the 110 volt wiring at the condenser was not covered.
Recent events (2)
- — I (S) $1224
- — Z (S) $2040
1910.305 B02 I
- Issued
- Jan 29, 2016
- Penalty
- Initial $2,040 · Current $1,224 Reduced
General-duty citation text
29 CFR 1910.305(b)(2)(i): Each outlet box in completed installations did not have a cover, faceplate, or fixture canopy: (a) On or about 10/13/2015 - Welding Shop, the 110 volt electrical light switch did not have a cover.
Recent events (2)
- — I (S) $1224
- — Z (S) $2040
More inspections at E C M Service, INC.
View E C M Service, INC.'s full OSHA safety record →
More inspections in this industry (NAICS 333911)
More inspections in AL
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 340985100.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.