Safety Incidents OSHA Severe Injury Reports · 2015–2025
5,189,992Inspections Most recent open 2026-07-18 Last loaded 2026-07-22

OSHA Inspection: BELL BOATS, INC.

Planned inspection · Health discipline

On , OSHA opened a planned health inspection of BELL BOATS, INC. in 2111 WEST MONROE AVENUE, PORT O CONNOR, TX 77982 (NAICS 336612). OSHA activity number 341140846.

What this inspection record means

OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.

Watch Bell Boats, INC. — free Get an email when a new federal OSHA severe-injury report for Bell Boats, INC. is published. One employer, no account, unsubscribe in one click.
Establishment
BELL BOATS, INC.
Site address
2111 WEST MONROE AVENUE
City
PORT O CONNOR
State
TX
ZIP
77982
Mailing
P.O. BOX 200, PORT O CONNOR, TX 77982
Inspection type
Planned (H)
Scope
Partial (B)
Discipline
Health
Advance notice
No
Union status
B
Opened
Closing conference
Case closed
Last modified
Data loaded
NAICS code
336612
Employees
16
Ownership type
A

7 citations on file for this inspection.

1910.134 C01

Serious Gravity 5 1 instance 11 exposed
Issued
Jun 17, 2016
Abate by
Jul 14, 2016
Penalty
Initial $2,400 · Current $1,440 Reduced

Hazardous substances 10731377P125

29 CFR 1910.134(c)(1): A written respiratory protection program that included the provisions in 29 CFR 1910.134(c)(1)(i) - (ix) with worksite specific procedures was not established and implemented for required respirator use:   On or about January 15th, 2016, and times prior thereto, at this facility, the employer had not established or implemented a respiratory protection program when employees were required to wear tight-fitting respirators when cutting fiberglass sheets, putting the adhesive and resin on fiberglass layers, pouring foam on the bottom of the boats and/or when boat parts were sprayed with hazardous chemicals.  An effective respiratory protection program would include, but not limited to:  a.    Procedures for selecting respirators for use in the work place; b.    medical evaluation of employees required to wear respirators; c.    a valid fit testing procedures for each type of tight-fitting respirators; d.    procedures and schedules for cleaning, disinfecting, storing, inspecting, repairing, discarding and maintaining           respirators; and, e.    training of employees in the proper use of respirators.
Recent events (2)
  • — I (S) $1440
  • — Z (S) $2400

1910.134 E01

Serious Gravity 5 1 instance 11 exposed
Issued
Jun 17, 2016
Abate by
Jul 14, 2016
Penalty
Initial $0 · Current $0

Hazardous substances 10731377P125

29 CFR 1910.134(e)(1): The employer did not provide a medical evaluation to determine the employee's ability to use a respirator, before the employee was fit tested or required to use the respirator in the workplace:  On or about January 15th, 2016, and times prior thereto, at this facility, the employer had not provided a medical evaluation to employees required to wear tight-fitting respirators when cutting fiberglass sheets, putting the adhesive and resin on fiberglass layers, pouring foam on the bottom of the boats and/or when boat parts were sprayed with hazardous chemicals.
Recent events (2)
  • — I (S) $0
  • — Z (S) $0

1910.134 F02

Serious Gravity 5 2 instances 1 exposed
Issued
Jun 17, 2016
Abate by
Jul 14, 2016
Penalty
Initial $0 · Current $0

Hazardous substances 10731377P125

29 CFR 1910.134(f)(2): Employee(s) using tight-fitting facepiece respirators were not fit tested whenever a different respirator facepiece (size, style, model or make) was used:  On or about January 28th, 2016, and times prior thereto, at this facility, employees were required to wear tight-fitting respirators when cutting fiberglass sheets, putting the adhesive and resin on fiberglass layers, pouring foam on the bottom of the boats and/or when boat parts were sprayed with hazardous chemicals.  The following respirators were worn:  a.    3M Reusable Half Face Respirator 7502 with 3M Organic Vapor Cartridge 6001; and,  b.    3M 8210 Particulate Respirator N95.
Recent events (2)
  • — I (S) $0
  • — Z (S) $0

1910.134 H02 I

Serious Gravity 5 1 instance 11 exposed
Issued
Jun 17, 2016
Abate by
Jul 14, 2016
Penalty
Initial $0 · Current $0

Hazardous substances 10731377P125

29 CFR 1910.134(h)(2)(i): Respirators were not stored to protect them from damage, contamination, dust, sunlight, extreme temperatures, excessive moisture, and damaging chemicals or  were not packed or stored to prevent deformation of the facepiece and exhalation valve:  On or about January 15th, 2016, and times prior thereto, at this facility, employees respirators were not stored properly to protect them from such as, but not limited to, dust and damaging chemicals from cutting fiberglass sheets, putting the adhesive and resin on fiberglass layers, pouring foam on the bottom of the boats and/or when boat parts were sprayed with hazardous chemicals.
Recent events (2)
  • — I (S) $0
  • — Z (S) $0

1910.134 K

Serious Gravity 5 1 instance 11 exposed
Issued
Jun 17, 2016
Abate by
Jul 14, 2016
Penalty
Initial $0 · Current $0

Hazardous substances 10731377P125

29 CFR 1910.134(k): The employer did not provide comprehensive, understandable training which did not occur annually and/or more often if necessary:  On or about January 28th, 2016, and times prior thereto, at this facility, the employer had not provided comprehensive training to employees who are required to use respirators to protect them when cutting fiberglass sheets, putting the adhesive and resin on fiberglass layers, pouring foam on the bottom of the boats or when boat parts were sprayed with hazardous chemicals.
Recent events (2)
  • — I (S) $0
  • — Z (S) $0

1910.1200 E01

Serious Gravity 5 1 instance 11 exposed
Issued
Jun 17, 2016
Abate by
Jul 14, 2016
Penalty
Initial $2,000 · Current $1,200 Reduced

Hazardous substances 10731377P125

29 CFR 1910.1200(e)(1): The employer did not develop, implement, and/or maintain at the workplace a written hazard communication program which describes how the criteria specified in 29 CFR 1910.1200(f), (g), and (h) will be met:  On or about January 28th, 2016, and times prior thereto, at this facility, employees were cutting fiberglass sheets, putting the adhesive and resin on fiberglass layers, pouring foam on the bottom of the boats or when boat parts were sprayed with hazardous chemicals such as, but not limited to, SP10PUF1 Isocyanates, SPRITZ-20-1.7-SP10PUF1 Catalyst, POLYCOR 970C981, 905 TR Mold Prep Cleaner, Acetone, STYPOL LHPC-2700 Resin, H&C Shark Grip Slip Resistant Additive, 970X900 SPEED PATCHAID and/or different types of coatings, industrial paint finishes and peroxides.  The employer had not developed a program which would address labeling and other forms of warning on chemicals containers, Safety Data Sheets and employees information and training on the hazards associated with chemicals used at this site.  The written program must also contain the following:  1.    a list of all hazardous chemicals on site; 2.    the methods the employer will use to inform employees of the hazards associated with non-routine tasks involving         chemicals, such as a spill; 3.    the hazards of chemicals contained in piping that is not labeled; and, 4.    the method the employer will use to inform other employers (contractors) of the chemicals their employees might           be exposed to while performing duties at this site.
Recent events (2)
  • — I (S) $1200
  • — Z (S) $2000

1910.1200 H01

Serious Gravity 5 1 instance 11 exposed
Issued
Jun 17, 2016
Abate by
Jul 14, 2016
Penalty
Initial $0 · Current $0

Hazardous substances 10731377P125

29 CFR 1910.1200(h)(1): Employees were not provided effective information and training on hazardous chemicals in their work area at the time of their initial assignment and whenever a new hazard that the employees had not been previously trained about was introduced into their work area:  On or about January 15th, 2016, and times prior thereto, at this facility, employees were cutting fiberglass sheets, putting the adhesive and resin on fiberglass layers, spraying foam on the bottom of the boats and/or when boat parts were sprayed with hazardous chemicals; employees were not provided an effective information and training on  the hazardous chemicals.
Recent events (2)
  • — I (S) $0
  • — Z (S) $0

This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 341140846.

Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.