OSHA Inspection: SYRACUSE LABEL CO., INC.

Issued

Feb 26, 2016

Abate by

Apr 1, 2016

Penalty

Initial $1,785 · Current $1,071 Reduced

General-duty citation text

29 CFR 1910.178(l)(4)(iii): An evaluation of each powered industrial truck operator's performance was not being conducted at least once every three years:    a)  At the establishment, on or about 2/9/16:  An evaluation of each powered industrial truck operator's performance was not done.    Abatement certification must be submitted for this item.

Issued

Feb 26, 2016

Abate by

Apr 1, 2016

Penalty

Initial $2,975 · Current $1,785 Reduced

General-duty citation text

29 CFR 1910.212(a)(1): One or more methods of machine guarding was not provided to protect the operator and other employees in the machine area from hazards such as those created by point of operation, ingoing nip points, rotating parts, flying chips and sparks:    a)  Maintenance Shop, on or about 2/9/16:  Rotating chuck on a South Bend lathe was not guarded.    b)  Roto Cell, on or about 2/9/16:  Ingoing nip points at the print deck cylinder areas and at the exit nips on Roto Presses R-7, R8-1, and R8-2 were not guarded.     Abatement certification must be submitted for these items.

Issued

Feb 26, 2016

Abate by

Apr 1, 2016

Penalty

Initial $2,975 · Current $1,785 Reduced

General-duty citation text

29 CFR 1910.219(d)(1): Pulley(s) with part(s) seven feet or less from the floor or work platform were not guarded in accordance with the requirements specified in 29 CFR 1910.219(m) and (o):    a)  Maintenance Shop, on or about 2/9/16:  Two sets of pulleys driving the South Bend lathe were not guarded.    Abatement certification must be submitted for this item.

Issued

Feb 26, 2016

Abate by

Apr 1, 2016

Penalty

Initial $0 · Current $0

General-duty citation text

29 CFR 1910.219(e)(1)(i): Horizontal belts which had both runs seven feet or less from the floor level were not guarded with a guard that extended to at least fifteen inches above the belt:  a)  Maintenance Shop, on or about 2/9/16:  One inch flat belt with metal lacings driving the South Bend lathe was not guarded.  Abatement certification must be submitted for this item.

Issued

Feb 26, 2016

Abate by

Apr 1, 2016

Penalty

Initial $0 · Current $0

General-duty citation text

29 CFR 1910.37(b)(2): Each exit was not clearly visible and marked by a sign reading "Exit":  a)  Receiving Dept., on or about 2/9/16:  Door used as an exit was not marked with an exit sign.  Abatement certification must be submitted for this item.

Issued

Feb 26, 2016

Abate by

Apr 1, 2016

Penalty

Initial $0 · Current $0

General-duty citation text

29 CFR 1910.147(c)(4)(ii): The energy control procedures did not clearly and specifically outline the scope, purpose, authorization, rules, and techniques to be utilized for the control of hazardous energy, including, but not limited to items (a) through (d) of this section:  a)  At the establishment, on or about 2/9/16:  The lockout/tagout procedures did not clearly and specifically outline the steps for shutting down, isolating, blocking and securing a machine or equipment to control hazardous energy for all sources of energy, specific steps for the placement and removal of lockout devices and the responsibility for them and specific steps for testing a machine or equipment to determine and verify the effectiveness of lockout devices.    Abatement certification must be submitted for this item.