HEATH, OH —
OSHA Inspection: IFORCE
Referral inspection · Safety discipline
At a glance
On , OSHA opened a referral safety inspection of IFORCE in 598 S. 30TH ST., HEATH, OH 43056 (NAICS 561311). OSHA activity number 341402329.
OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- IFORCE
- Site address
- 598 S. 30TH ST.
- City
- HEATH
- State
- OH
- ZIP
- 43056
- Mailing
- 598 S. 30TH ST., HEATH, OH 43056
What kind of inspection was it?
- Inspection type
- Referral (C)
- Scope
- Partial (B)
- Discipline
- Safety
- Advance notice
- No
- Union status
- B
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 561311
- Employees
- 310
- Ownership type
- A
Citations
2 citations on file for this inspection.
1910.147 C07 I B
- Issued
- Jun 29, 2016
- Abate by
- Aug 22, 2016
- Penalty
- Initial $7,000 · Current $5,000 Reduced
General-duty citation text
29 CFR 1910.147(c)(7)(i): General. Training and communication. The employer shall provide training to ensure that the purpose and function of the energy control program are understood by employees and that the knowledge and skills required for the safe application, usage, and removal of the energy controls are acquired by employees. The training shall include the following: 29 CFR 1910.147(c)(7)(i)(B): Each affected employee shall be instructed in the purpose and use of the energy control procedure: a. The employer failed to perform training, or assure that training was performed, for temporary workers as affected employees under the lockout/tagout standard. iforce supplies temporary workers, who work in areas where service and maintenance activities on mechanical power presses are performed, to Sunfield, Inc. The employees were not provided training on the purpose and use of the hazardous energy control program prior to being assigned work in these areas, exposing them to crushing and caught-in hazards at Sunfield, Inc.
Recent events (2)
- — I (S) $5000
- — Z (S) $7000
1910.217 F02
- Issued
- Jun 29, 2016
- Abate by
- Aug 4, 2016
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.217(f)(2): Instruction to operators. The employer shall train and instruct the operator in the safe method of work before starting work on any operation covered by this section. The employer shall insure by adequate supervision that correct operating procedures are being followed. a. The employer failed to perform training, or assure that training was performed, in mechanical power press safe method of operating for temporary workers supplied to Sunfield, Inc. Temporary workers do not receive safe method of operation training prior to being assigned to operate power presses from iforce, from Sunfield, Inc. or in some combined fashion by these shared employers.
Recent events (2)
- — I (S) $0
- — Z (S) $0
More inspections at Iforce
View Iforce's full OSHA safety record →
More inspections in this industry (NAICS 561311)
More inspections in OH
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 341402329.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.