TIPP CITY, OH —
OSHA Inspection: DAP PRODUCTS, INC.
Referral inspection · Safety discipline
At a glance
On , OSHA opened a referral safety inspection of DAP PRODUCTS, INC. in 875 NORTH 3RD ST., TIPP CITY, OH 45371 (NAICS 325520). OSHA activity number 341572451.
OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- DAP PRODUCTS, INC.
- Site address
- 875 NORTH 3RD ST.
- City
- TIPP CITY
- State
- OH
- ZIP
- 45371
- Mailing
- 875 NORTH 3RD ST., TIPP CITY, OH 45371
What kind of inspection was it?
- Inspection type
- Referral (C)
- Scope
- Partial (B)
- Discipline
- Safety
- Advance notice
- No
- Union status
- B
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 325520
- Employees
- 78
- Ownership type
- A
Citations
4 citations on file for this inspection.
1910.147 C07 I A
- Issued
- Jul 29, 2016
- Abate by
- Aug 24, 2016
- Penalty
- Initial $7,000 · Current $0 Reduced
General-duty citation text
29 CFR 1910.147(c)(7)(i)(A): Each authorized employee shall receive training in the recognition of applicable hazardous energy sources, the type and magnitude of the energy available in the workplace, and the methods and means necessary for energy isolation and control. a) On June 17, 2016 employees who remove jams on the Aerosol Paint Line was not trained as an authorized lockout employee in that during the removal of a jam the employees would turn the machine off, remove the jam and not lockout.
Recent events (2)
- — I (S) $0
- — Z (S) $7000
1910.147 D
- Issued
- Jul 29, 2016
- Abate by
- Aug 24, 2016
- Penalty
- Initial $7,000 · Current $0 Reduced
General-duty citation text
29 CFR 1910.147(d): Application of control. The established procedures for the application of energy control (the lockout or tagout procedures) shall cover the following elements and actions and shall be done in the following sequence: a) Employees who perform servicing and/or maintenance on or around the Aerosol Labeler Line were not required to: (1) Physically locate and operate the electrical disconnect in such a manner as to isolate the machine or equipment from the energy source. (2) Affix a lockout or tagout devices to the electrical disconnect.
Recent events (2)
- — I (S) $0
- — Z (S) $7000
1910.147 F01
- Issued
- Jul 29, 2016
- Abate by
- Aug 24, 2016
- Penalty
- Initial $7,000 · Current $7,000
General-duty citation text
29 CFR 1910.147(f)(1): Testing or positioning of machines, equipment or components thereof. In situations in which lockout or tagout devices must be temporarily removed from the energy isolating device and the machine or equipment energized to test or position the machine, equipment or component thereof, the following sequence of actions shall be followed: Employees performing testing or positioning of machine or equipment did not perform the following: (1) Remove the equipment from the machine or equipment area in accordance with (e)(2) (2) Deenergize all systems and reapply energy control measures in accordance with paragraph (d) to continue with servicing and/or maintenance. (a) On June 17, 2016 while unjamming the Aerosol Paint Line, the machine was not isolated to prevent from start ups.
Recent events (2)
- — I (O) $7000
- — Z (S) $7000
1910.219 E01 I
- Issued
- Jul 29, 2016
- Abate by
- Sep 30, 2016
- Penalty
- Initial $7,000 · Current $7,000
General-duty citation text
29 CFR 1910.219(e)(1)(i): Where both runs of horizontal belts are seven (7) feet or less from the floor level, the guard shall extend to at least fifteen (15) inches above the belt or to a standard height, except that where both runs of a horizontal belt are 42 inches or less from the floor, the belt shall be fully enclosed in accordance with paragraphs (m) and (o) of this section. a) On June 17, 2016 machine guarding was not in place and/or attached over the belt and pulley for the main motor drive for the Aerosol Paint Line bottom section, exposing employees to pinch point hazards. b) Machine guarding was inadequate on the Aerosol Paint line upper section, in that employees can reach, pull and turn the line when there is a jam, exposing them to pinch point hazards.
Recent events (2)
- — I (O) $7000
- — Z (S) $7000
More inspections at DAP Products, INC.
View DAP Products, INC.'s full OSHA safety record →
More inspections in this industry (NAICS 325520)
More inspections in OH
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 341572451.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.