MANITOWOC, WI —
OSHA Inspection: COLOR CRAFT GRAPHIC ARTS
Complaint inspection · Safety discipline
At a glance
On , OSHA opened a complaint safety inspection of COLOR CRAFT GRAPHIC ARTS in 5631 WEST DRIVE, MANITOWOC, WI 54220 (NAICS 541430). OSHA activity number 341607042.
What this inspection record means
OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Watch Color Craft Graphic Arts — free
Get an email when a new federal OSHA severe-injury report for Color Craft Graphic Arts is published. One employer, no account, unsubscribe in one click.
Where did this inspection happen?
- Establishment
- COLOR CRAFT GRAPHIC ARTS
- Site address
- 5631 WEST DRIVE
- City
- MANITOWOC
- State
- WI
- ZIP
- 54220
- Mailing
- 5631 WEST DRIVE, MANITOWOC, WI 54220
What kind of inspection was it?
- Inspection type
- Complaint (B)
- Scope
- Partial (B)
- Discipline
- Safety
- Advance notice
- No
- Union status
- B
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 541430
- Employees
- 65
- Ownership type
- A
Citations
7 citations on file for this inspection.
1910.147 C07 I B
- Issued
- Aug 1, 2016
- Abate by
- Aug 23, 2016
- Penalty
- Initial $2,380 · Current $1,666 Reduced
General-duty citation text
29 CFR 1910.147(c)(7)(i)(B): Affected employees were not instructed in the purpose and use of the energy control procedure: a) On or about July 8, 2016 the employer did not provide affected employees in the purpose and use of energy control procedures.
Recent events (2)
- — I (S) $1666
- — Z (S) $2380
1910.219 C02 I
- Issued
- Aug 1, 2016
- Abate by
- Aug 30, 2016
- Penalty
- Initial $3,570 · Current $2,499 Reduced
General-duty citation text
29 CFR 1910.219(c)(2)(i): All exposed part(s) of horizontal shafting seven (7) feet or less from floor or working platform were not protected by stationary casing(s) enclosing shafting completely or by trough(s) enclosing sides and top or sides and bottom of shafting: a) On or about July 8, 2016 unguarded rotating shafts along the #1 Vega 750 folder gluer, exposed employees feeding and operating the machine to entanglement hazards. b) On or about July 8, 2016 unguarded rotating shafts along the #2 Vega 750 folder gluer, exposed employees feeding and operating the machine to entanglement hazards. c) On or about July 8, 2016 unguarded rotating shafts along the Signature 110 CS folder gluer, exposed employees feeding and operating the machine to entanglement hazards.
Recent events (2)
- — I (S) $2499
- — Z (S) $3570
1910.219 D01
- Issued
- Aug 1, 2016
- Abate by
- Aug 30, 2016
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.219(d)(1): Pulley(s) with part(s) seven feet or less from the floor or work platform were not guarded in accordance with the requirements specified in 29 CFR 1910.219(m) and (o): a) On or about July 8, 2016 in-running nip points created by unguarded belts and pulleys along the #1 Vega 750 folder gluer, exposed employees feeding and operating the machine to entanglement hazards. b) On or about July 8, 2016 in-running nip points created by unguarded belts and pulleys along the #2 Vega 750 folder gluer, exposed employees feeding and operating the machine to entanglement hazards. c) On or about July 8, 2016 in-running nip points created by unguarded belts and pulleys along the Signature 110 CS folder gluer, exposed employees feeding and operating the machine to entanglement hazards.
Recent events (2)
- — I (S) $0
- — Z (S) $0
1910.219 E01 I
- Issued
- Aug 1, 2016
- Abate by
- Aug 30, 2016
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.219(e)(1)(i): Horizontal belts where both runs were 42 inches or less from the floor or platform, were not fully enclosed in accordance with paragraphs (m) and (o) of this section: a) On or about July 8, 2016 in-running nip points created by unguarded horizontal belts and pulleys along the #1 Vega 750 folder gluer, exposed employees feeding and operating the machine to entanglement hazards. b) On or about July 8, 2016 in-running nip points created by unguarded horizontal belts and pulleys along the #2 Vega 750 folder gluer, exposed employees feeding and operating the machine to entanglement hazards. c) On or about July 8, 2016 in-running nip points created by unguarded horizontal belts and pulleys along the Signature 110 CS folder gluer, exposed employees feeding and operating the machine to entanglement hazards.
Recent events (2)
- — I (S) $0
- — Z (S) $0
1910.219 E03 I
- Issued
- Aug 1, 2016
- Abate by
- Aug 30, 2016
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.219(e)(3)(i): Vertical and inclined belts shall be enclosed by a guard conforming to standards in paragraphs (m) and (o) of this section. a) On or about July 8, 2016 in-running nip points created by unguarded vertical belts and pulleys along the #1 Vega 750 folder gluer, exposed employees feeding and operating the machine to entanglement hazards. b) On or about July 8, 2016 in-running nip points created by unguarded vertical belts and pulleys along the #2 Vega 750 folder gluer, exposed employees feeding and operating the machine to entanglement hazards. c) On or about July 8, 2016 in-running nip points created by unguarded vertical belts and pulleys along the Signature 110 CS folder gluer, exposed employees feeding and operating the machine to entanglement hazards.
Recent events (2)
- — I (S) $0
- — Z (S) $0
1910.147 C06 I A
- Issued
- Aug 1, 2016
- Abate by
- Aug 15, 2016
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.147(c)(6)(i)(A): The periodic inspection of the energy control procedure was not performed by an authorized employee other than the one utilizing the energy control procedure being inspected: a) On or about June 24, 2016 the employer did not have an authorized employee conduct the annual periodic inspections for the energy control procedures.
Recent events (2)
- — I (O) $0
- — Z (O) $0
1910.157 G01
- Issued
- Aug 1, 2016
- Abate by
- Aug 15, 2016
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.157(g)(1): An educational program was not provided for all employees to familiarize them with the general principles of fire extinguisher use and the hazards involved with incipient stage fire fighting: a) On or about July 8, 2016 the employer did not provide employees with training to familiarize them with general principles of fire extinguisher use and/or the hazards involved with incipient stage fire fighting on an annual basis.
Recent events (2)
- — I (O) $0
- — Z (O) $0
More inspections in this industry (NAICS 541430)
Jun 10, 2026
Hybrid Design Services · TROY, MI
Jun 3, 2026
Graphic Image · WILLIAMSTOWN, NJ
Apr 27, 2026
Jrba Ventures LLC · BEAR, DE
Apr 16, 2026
Trimline Graphics International · HIALEAH, FL
Apr 15, 2026
KNG Visual Solutions · SANTA ROSA, CA
More inspections in WI
Jul 24, 2026
Walzcraft Industries, INC. · LA CROSSE, WI
Jul 24, 2026
E & M Building LLC · MILWAUKEE, WI
Jul 23, 2026
Triple M Construction LLC · MERRILL, WI
Jul 23, 2026
Metallics, INC. · ONALASKA, WI
Jul 23, 2026
Best Plumbing of MT. Calvary, LLC · ELKHART LAKE, WI
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 341607042.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.