Safety Incidents OSHA Severe Injury Reports · 2015–2025
5,189,992Inspections Most recent open 2026-07-18 Last loaded 2026-07-22

OSHA Inspection: MIDLANTIC PALLET, LLC

Complaint inspection · Safety discipline

On , OSHA opened a complaint safety inspection of MIDLANTIC PALLET, LLC in 379 S. ALBEMARLE STREET, YORK, PA 17403 (NAICS 321920). OSHA activity number 341747889.

What this inspection record means

OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.

Watch Midlantic Pallet, LLC — free Get an email when a new federal OSHA severe-injury report for Midlantic Pallet, LLC is published. One employer, no account, unsubscribe in one click.
Site address
379 S. ALBEMARLE STREET
City
YORK
State
PA
ZIP
17403
Mailing
PO BOX 3616, YORK, PA 17402
Inspection type
Complaint (B)
Scope
Partial (B)
Discipline
Safety
Advance notice
No
Union status
B
Opened
Closing conference
Case closed
Last modified
Data loaded
NAICS code
321920
Employees
20
Ownership type
A

6 citations on file for this inspection.

5(a)(1)

Serious Gravity 5 1 instance 3 exposed
Issued
Nov 15, 2016
Abate by
Dec 12, 2016
Penalty
Initial $2,850 · Current $2,850
OSH ACT of 1970 Section (5)(a)(1): The employer did not furnish employment and a place of employment which was free from recognized hazards that were causing or likely to cause death or serious physical harm to employees in that employees were exposed to the hazard of getting caught-in or between a tipping forklift and the ground:  a) 379 S. Albemarle Street, York PA - On or about September 2, 2016, employees were observed operating Unicarriers forklifts without the use of the manufactured installed seatbelt, exposing them to crushing injuries associated with tipover hazards.  Abatement certification required within 10 days after abatement date. The certification shall include a statement that abatement is complete, date and method of abatement, and states employees and their representatives were informed of this abatement.
Recent events (2)
  • — I (S) $2850
  • — Z (S) $2850

1910.178 L01 II

Serious Gravity 5 1 instance 3 exposed
Issued
Nov 15, 2016
Abate by
Jan 27, 2017
Penalty
Initial $2,850 · Current $2,850
29 CFR 1910.178(l)(1)(ii): The employer did not ensure that each powered industrial truck operator was competent to operate a powered industrial truck safely, as demonstrated by the successful completion of the training and evaluation specified in this paragraph (l).    a) 379 S. Albemarle Street, York PA - On or about September 2, 2016, employees were observed operating forklifts to move material around the yard and load/unload trailers and had not completed employer training and evaluation, exposing employees to struck-by hazards.    Abatement certification required within 10 days after abatement date. The certification shall include a statement that abatement is complete, date and method of abatement, and states employees and their representatives were informed of this abatement.
Recent events (2)
  • — I (S) $2850
  • — Z (S) $2850

1910.212 B

Deleted Serious Gravity 1 1 instance 3 exposed
Issued
Nov 15, 2016
Abate by
Dec 12, 2016
Penalty
Initial $2,138 · Current $0 Reduced
29 CFR 1910.212(b): Machine(s) designed for fixed location(s) were not securely anchored to prevent walking or moving:  a) 379 S. Albemarle Street, York PA - A chop saw was not secured to the floor to prevent walking or moving exposing employees to struck-by hazards, on or about September 2, 2016. The saw fitted with tabs at its base.  Abatement certification required within 10 days after abatement date. The certification shall include a statement that abatement is complete, date and method of abatement, and states employees and their representatives were informed of this abatement.
Recent events (2)
  • — I (S) $0
  • — Z (S) $2138

1910.303 G01

Serious Gravity 1 1 instance 3 exposed
Issued
Nov 15, 2016
Abate by
Dec 12, 2016
Penalty
Initial $2,138 · Current $1,284 Reduced
29 CFR 1910.303(g)(1): Sufficient access and working space was not provided and maintained about all electric equipment (operating at 600 volts, nominal, or less to ground) to permit ready and safe operation and maintenance of such equipment:    a) 379 S. Albemarle Street, York PA; Chop Saw - On or about September 2, 2016, a disconnect switch was blocked by two OSB plywood sheets.    b) 370 S. Albemarle Street, York PA; Trim Saw - On or about September 2, 2016, a disconnect switch was blocked by two OSB plywood sheets.    Abatement certification required within 10 days after abatement date. The certification shall include a statement that abatement is complete, date and method of abatement, and states employees and their representatives were informed of this abatement.
Recent events (2)
  • — I (S) $1284
  • — Z (S) $2138

1910.132 D01

Other-than-serious 1 instance 20 exposed
Issued
Nov 15, 2016
Abate by
Dec 19, 2016
Penalty
Initial $0 · Current $0
29 CFR 1910.132(d)(1): The employer did not assess the workplace to determine if hazards were present, or likely to be present, which necessitate the use of personal protective equipment.  a) 379 S. Albemarle Street, York PA - On or about September 2, 2016, a workplace hazard assessment was not conducted where employees are exposed to flying wood chips and debris and struck-by injuries while using equipment such as, but not limited to chain saws, chops saws, trim saws, and band saws to build and dispose of wooden pallets.  Abatement certification required within 10 days after abatement date. The certification shall include a statement that abatement is complete, date and method of abatement, and states employees and their representatives were informed of this abatement.
Recent events (2)
  • — I (O) $0
  • — Z (O) $0

1910.334 A02 I

Other-than-serious 1 instance 2 exposed
Issued
Nov 15, 2016
Penalty
Initial $0 · Current $0
29 CFR 1910.334(a)(2)(i): Portable cord and plug connected equipment and flexible cord sets (extension cords) were not visually inspected before use on any shift for external defects (such as loose parts, deformed and missing pins, or damage to outer jacket or insulation) and for evidence of possible internal damage (such as pinched or crushed outer jacket):  a) 379 S. Albemarle Street, York PA - On or about September 2, 2016, the employer did not ensure that the cord on a portable hand lamp was examined for damage. The outer jacket near the handle was damaged exposing the inner insulation.  No abatement certification or documentation required.
Recent events (2)
  • — I (O) $0
  • — Z (O) $0

This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 341747889.

Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.