WILLIS, TX —
OSHA Inspection: H & R MFG. AND SUPPLY, INC.
Complaint inspection · Health discipline
At a glance
On , OSHA opened a complaint health inspection of H & R MFG. AND SUPPLY, INC. in 12400 ROSE ROAD, WILLIS, TX 77378 (NAICS 332710). OSHA activity number 341777498.
OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- H & R MFG. AND SUPPLY, INC.
- Site address
- 12400 ROSE ROAD
- City
- WILLIS
- State
- TX
- ZIP
- 77378
- Mailing
- 12400 ROSE ROAD, WILLIS, TX 77378
What kind of inspection was it?
- Inspection type
- Complaint (B)
- Scope
- Partial (B)
- Discipline
- Health
- Advance notice
- No
- Union status
- B
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 332710
- Employees
- 30
- Ownership type
- A
Citations
5 citations on file for this inspection.
5(a)(1)
- Issued
- Mar 14, 2017
- Penalty
- Initial $6,338 · Current $3,169 Reduced
General-duty citation text
OSH ACT of 1970 Section (5)(a)(1): The employer does not furnish to each of his employees employment and a place of employment which are free from the recognized hazards of being struck-by which are causing or likely to cause death or serious physical harm to employees: On or about September 15, 2016 in the manufacturing shop near L26/L21, where employees were exposed to struck-by hazards when operating a floor-mounted jib crane (serial #1530 ML) that did not have a safety latch on the hook.
Recent events (2)
- — I (S) $3169
- — Z (S) $6338
1910.23 D01 II
- Issued
- Mar 14, 2017
- Penalty
- Initial $5,070 · Current $2,535 Reduced
General-duty citation text
29 CFR 1910.23(d)(1)(ii): Stairway(s) less than 44 inches wide having one side open, did not have at least one stair railing on the open side: On or about September 15, 2016 at the entrance to the office, employees were exposed to a fall hazard when traveling up and down a stairway that did not have a stair rail on its right ascending side.
Recent events (2)
- — I (S) $2535
- — Z (S) $5070
1910.179 G01 V
- Issued
- Mar 14, 2017
- Penalty
- Initial $6,338 · Current $3,169 Reduced
General-duty citation text
29 CFR 1910.179(g)(1)(v): Pendant control box(es) were not clearly marked for identification of functions: On or about September 15, 2016 in the saw shop, employees were exposed to struck-by hazards when lifting steel bars using a five ton Gaffey crane (serial# 00J02737) that was not clearly marked for identification of function on the pendant controls.
Recent events (2)
- — I (S) $3169
- — Z (S) $6338
1910.212 A01
- Issued
- Mar 14, 2017
- Penalty
- Initial $6,338 · Current $3,169 Reduced
General-duty citation text
29 CFR 1910.212(a)(1): One or more methods of machine guarding was not provided to protect the operator and other employees in the machine area from hazards such as those created by point of operation, ingoing nip points, rotating parts, flying chips and sparks: On or about September 15, 2016: a. In the manufacturing shop where operators were exposed to struck -by and caught-in hazards when operating the CNC mill #M42 (Serial# VC 9096) b. In the manufacturing shop where operators were exposed to struck- by and caught-in hazards when operating the CNC mill # M44 ( Serial # VN 1339). c. In the manufacturing shop where operators were exposed to struck- by and caught-in hazards when operating the CNC mill 51 (Serial# MLA 4466). d. In the manufacturing shop where operators were exposed to struck- by and caught-in hazards when operating the CNC mill #54 (Serial #29899)
Recent events (2)
- — I (S) $3169
- — Z (S) $6338
1910.242 B
- Issued
- Mar 14, 2017
- Penalty
- Initial $3,802 · Current $1,901 Reduced
General-duty citation text
29 CFR 1910.242(b): Compressed air used for cleaning purposes was not reduced to less than 30 p.s.i. On or about September 15, 2016: a. In the manufacturing shop, near CNC machine#M29 where employees were exposed to struck-by hazards when using compressed air greater than 30 p.s.i. to blow loose metal particles off recently milled nuts and other accessories. b. In the manufacturing shop, near CNC machine#M44 where employees were exposed to struck-by hazards when using compressed air greater than 30 p.s.i. to blow loose metal particles off recently milled nuts and other accessories. c. In the manufacturing shop, near CNC machine#M47 where employees were exposed to struck-by hazards when using compressed air greater than 30 p.s.i. to blow loose metal particles off recently milled nuts and other accessories. d. In the manufacturing shop, near CNC machine#M51 where employees were exposed to struck-by hazards when using compressed air greater than 30 p.s.i. to blow loose metal particles off recently milled nuts and other accessories.
Recent events (2)
- — I (S) $1901
- — Z (S) $3802
More inspections at H & R MFG. and Supply, INC.
View H & R MFG. and Supply, INC.'s full OSHA safety record →
More inspections in this industry (NAICS 332710)
More inspections in TX
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 341777498.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.