HELENA, MT —
OSHA Inspection: BMC
Planned inspection · Safety discipline
At a glance
On , OSHA opened a planned safety inspection of BMC in 790 NICOLE STREET, HELENA, MT 59601 (NAICS 321214). OSHA activity number 341839975.
OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- BMC
- Site address
- 790 NICOLE STREET
- City
- HELENA
- State
- MT
- ZIP
- 59601
- Mailing
- 790 NICOLE STREET, HELENA, MT 59601
What kind of inspection was it?
- Inspection type
- Planned (H)
- Scope
- Complete (A)
- Discipline
- Safety
- Advance notice
- No
- Union status
- B
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 321214
- Employees
- 17
- Ownership type
- A
Citations
3 citations on file for this inspection.
1910.219 C04 I
- Issued
- Feb 6, 2017
- Abate by
- Mar 3, 2017
- Penalty
- Initial $4,889 · Current $2,933 Reduced
General-duty citation text
29 CFR 1910.219(c)(4)(i): Shaft ends projecting more than one-half the diameter of the shaft were not guarded by nonrotating caps or safety sleeves: a) South east end of facility: On or about October 12, 2016 and at times prior, employees were exposed to caught by hazards of the exposed shafts on the front outer sides of the conveyor table, which is part of the Auto-Omni, Robotic Component Saw operation.
Recent events (2)
- — I (O) $2933.4
- — Z (S) $4889
1910.219 D01
- Issued
- Feb 6, 2017
- Abate by
- Mar 3, 2017
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.219(d)(1): Pulley(s) with part(s) seven feet or less from the floor or work platform were not guarded in accordance with the requirements specified in 29 CFR 1910.219(m) and (o): a) South east end of facility: On or about October 12, 2016 and at times prior, employees were exposed to caught in hazards while working in and around the unguarded pulley on the motor operating the shaker pan of the Auto-Omni, Robotic Component Saw.
Recent events (2)
- — I (O) $0
- — Z (S) $0
1910.219 E01 I
- Issued
- Feb 6, 2017
- Abate by
- Mar 3, 2017
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.219(e)(1)(i): Horizontal belts of seven (7) feet or less from the floor level, the guard shall extent to at least fifteen (15) inches above the belt or to a standard height except that where both runs of a horizontal belt are 42 inches or less from the floor, the belt shall be fully enclosed: a) South east end of facility: On or about October 12, 2016 and at times prior, employees were exposed to caught in hazards while working in and around the unguarded belt of the shaker pan motor on the Auto-Omni Robotic Component Saw.
Recent events (2)
- — I (O) $0
- — Z (S) $0
More inspections at BMC
View BMC's full OSHA safety record →
More inspections in this industry (NAICS 321214)
More inspections in MT
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 341839975.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.