Safety Incidents OSHA Severe Injury Reports · 2015–2025
2,004,209Inspections Most recent open 2026-07-13 Last loaded 2026-07-17

OSHA Inspection: SIMONTON BUILDING PRODUCTS, LLC.

Complaint inspection · Safety discipline

On , OSHA opened a complaint safety inspection of SIMONTON BUILDING PRODUCTS, LLC. in 1 COCHRANE DRIVE, PENNSBORO, WV 26415 (NAICS 326199). OSHA activity number 341855898.

Watch Simonton Building Products, LLC. — free Get an email when a new federal OSHA severe-injury report for Simonton Building Products, LLC. is published. One employer, no account, unsubscribe in one click.
Site address
1 COCHRANE DRIVE
City
PENNSBORO
State
WV
ZIP
26415
Mailing
1 COCHRANE DRIVE, PENNSBORO, WV 26415
Inspection type
Complaint (B)
Scope
Partial (B)
Discipline
Safety
Advance notice
No
Union status
B
Opened
Closing conference
Case closed
Last modified
Data loaded
NAICS code
326199
Employees
640
Ownership type
A

4 citations on file for this inspection.

5(a)(1)

Deleted Serious Gravity 5 1 instance 4 exposed
Issued
Abate by
Penalty
Initial $7696.00 · Current $0.00 Reduced
OSH ACT of 1970 Section (5)(a)(1):  The employer did not furnish employment and a place of employment which was free from recognized hazards that were causing or likely to cause death or serious physical harm to employees in that employees were exposed to severe lacerations and amputation hazards from unintended activation of the saw blade:    (a) 1201-5000 Frame Department:  On or about October 13, 2016 and times prior, the Norgren foot pedal, used to actuate the 12 inch saw blade on the SC12 Sampson cutoff saw, was not fully guarded.
Recent events (2)
  • — I (S) $0
  • — Z (S) $7696

1910.212 A01

Serious Gravity 10 1 instance 4 exposed
Issued
Abate by
Penalty
Initial $12675.00 · Current $11175.00 Reduced
29 CFR 1910.212(a)(1): One or more methods of machine guarding was not provided to protect the operator and other employees in the machine area from hazards such as those created by point of operation, ingoing nip points, rotating parts, flying chips and sparks:    (a) 1201-5000 Frame Department:  On or about September 23, 2016 and times prior, the Sampson SC12 cutoff saw, Serial Number 5922, was not guarded to prevent employees from making contact with the 12 inch rotating blade.
Recent events (2)
  • — I (S) $11175
  • — Z (S) $12675

1910.147 D03

Deleted Serious Gravity 10 1 instance 1 exposed
Issued
Abate by
Penalty
Initial $0.00 · Current $0.00
29 CFR 1910.147(d)(3): All energy isolating devices that were needed to control the energy to the machine or equipment were not physically located and operated in such a manner as to isolate the machine or equipment from the energy source(s):  (a) 1201-5000 Frame Department: On or about September 23, 2016 and times prior, the Sampson SC12 cutoff saw was not de-energized by disconnecting the electrical power and the airline prior to reaching into the saw through the guard opening to remove vinyl debris and scrap near the point of operation.
Recent events (2)
  • — I (S) $0
  • — Z (S) $0

1910.147 C06 II

Other-than-serious 1 instance 4 exposed
Issued
Abate by
Penalty
Initial $0.00 · Current $0.00
29 CFR 1910.147(c)(6)(ii): The employer did not certify that periodic inspections of the energy control procedures had been performed:  (a)  Pennsboro Facility:  On or about October 13, 2016 and times prior, the employer did not certify that periodic inspections were conducted of the energy control procedures in 2016.
Recent events (2)
  • — I (O) $0
  • — Z (O) $0

This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 341855898.