N DIGHTON, MA ·
OSHA Inspection: BOSTON SASH AND MILLWORK INCORPORATED
Planned inspection · Safety discipline
At a glance
On , OSHA opened a planned safety inspection of BOSTON SASH AND MILLWORK INCORPORATED in 667 SPRING STREET, N DIGHTON, MA 02764 (NAICS 321918). OSHA activity number 342131992.
OSHA opens inspections for many reasons: routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- BOSTON SASH AND MILLWORK INCORPORATED
- Site address
- 667 SPRING STREET
- City
- N DIGHTON
- State
- MA
- ZIP
- 02764
- Mailing
- P.O. BOX 345, N DIGHTON, MA 02764
What kind of inspection was it?
- Inspection type
- Planned (H)
- Scope
- Partial (B)
- Discipline
- Safety
- Advance notice
- No
- Union status
- B
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 321918
- Employees
- 17
- Ownership type
- A
Citations
6 citations on file for this inspection.
1910.147 C01
- Issued
- Mar 3, 2017
- Abate by
- Apr 21, 2017
- Penalty
- Initial $3,078 · Current $2,155 Reduced
General-duty citation text
29 CFR 1910.147(c)(1): The employer did not establish a program consisting of an energy control procedure, employee training and periodic inspections to ensure that before any employee performed any servicing or maintenance on a machine or equipment where the unexpected energizing, startup or release of stored energy could occur and cause injury, the machine or equipment shall be isolated from the energy source and rendered inoperative: Worksite: The employer did not develop a written lockout tagout program.
Recent events (2)
- · I (S) $2154.6
- · Z (S) $3078
1910.213 H01
- Issued
- Mar 3, 2017
- Abate by
- Jul 18, 2017
- Penalty
- Initial $3,078 · Current $2,155 Reduced
General-duty citation text
29 CFR 1910.213(h)(1): The sides of the lower exposed portion of the blade of radial saw(s) were not guarded to the full diameter of the blade by a device that automatically adjusted itself to the thickness of the stock and remained in contact with the stock: Center of the Shop: The lower sides of The Original Radial Arm Saw with the dadoo blade were not guarded.
Recent events (2)
- · I (S) $2154.6
- · Z (S) $3078
1910.213 H03
- Issued
- Mar 3, 2017
- Abate by
- Jul 18, 2017
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.213(h)(3): Radial saw(s) were not provided with an adjustable stop to prevent the forward travel of the blade beyond the position necessary to complete the cut in repetitive operations: Center of the Shop: The cutting head of The Champion Radial Arm Saw traveled past the end of the table.
Recent events (2)
- · I (S) $0
- · Z (S) $0
1910.178 L04 I
- Issued
- Mar 3, 2017
- Abate by
- Apr 21, 2017
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.178(l)(4)(i): 1910.178(l)(4)(iii): An evaluation of each powered industrial truck operator's performance shall be conducted at least once every three years. Worksite: All operators of the forklift were not retrained within three years.
Recent events (2)
- · I (O) $0
- · Z (O) $0
1910.178 P01
- Issued
- Mar 3, 2017
- Abate by
- Apr 21, 2017
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.178(p)(1): Powered industrial truck(s) found to be in need of repair, defective, or in any way unsafe had not been taken out of service until restored to safe operating conditions: Back of the Shop: The Yale Fork Lift had a broken horn, a broken hydraulic hose pulley, and a broken emergency brake.
Recent events (2)
- · I (O) $0
- · Z (O) $0
1910.219 D01
- Issued
- Mar 3, 2017
- Abate by
- Apr 21, 2017
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.219(d)(1): Pulley(s) with part(s) seven feet or less from the floor or work platform were not guarded in accordance with the requirements specified in 29 CFR 1910.219(m) and (o): Back of the Shop: The pulley and belt drive of the two sided planer was not completely enclosed by a guard.
Recent events (2)
- · I (O) $0
- · Z (O) $0
More inspections in this industry (NAICS 321918)
More inspections in MA
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 342131992.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.