MASSILLON, OH ·
OSHA Inspection: FIBERCORR MILLS, LLC.
Referral inspection · Safety discipline
At a glance
On , OSHA opened a referral safety inspection of FIBERCORR MILLS, LLC. in 670 17TH ST. N.W., MASSILLON, OH 44646 (NAICS 322299). OSHA activity number 342319100.
OSHA opens inspections for many reasons: routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- FIBERCORR MILLS, LLC.
- Site address
- 670 17TH ST. N.W.
- City
- MASSILLON
- State
- OH
- ZIP
- 44646
- Mailing
- 670 17TH ST. N.W., MASSILLON, OH 44646
What kind of inspection was it?
- Inspection type
- Referral (C)
- Scope
- Partial (B)
- Discipline
- Safety
- Advance notice
- No
- Union status
- B
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 322299
- Employees
- 87
- Ownership type
- A
Citations
2 citations on file for this inspection.
1910.147 D
- Issued
- Jun 14, 2017
- Abate by
- Jul 11, 2017
- Penalty
- Initial $8,873 · Current $6,211 Reduced
General-duty citation text
29 CFR 1910.147(d): The established procedure for the application of energy control (the lockout or tagout procedures) did not cover the actions listed in and was not done in sequence as required by 29 CFR 1910.147(d)(1)-(6): On or about 5/12/2017, the employees tasked with wiping off debris from the cleaning blades, did not conduct the following procedures to control hazardous energy as required by 29 CFR 1910.147(d)(1)-(6): 1) The machine or equipment was not turned off or shut down using the procedures established for the machine or equipment, 2) All energy isolating devices that were needed to control the energy to the machine or equipment were not physically located and operated in such a manner as to isolate the machine or equipment from the energy source(s), 3) A lockout device was not attached to all power sources, 4) Locks, tags, chains, wedges, key blocks, adapter pins, self-locking fasteners, or other hardware shall be provided by the employer for isolating, securing or blocking of machines or equipment from energy sources, 5) Prior to starting work on machines or equipment that had been locked out or tagged out, the authorized employee did not verify that isolation and deenergization of the machine or equipment had been accomplished.
Recent events (2)
- · I (S) $6211.1
- · Z (S) $8873
1910.212 A01
- Issued
- Jun 14, 2017
- Abate by
- Aug 30, 2017
- Penalty
- Initial $8,873 · Current $0 Reduced
General-duty citation text
29 CFR 1910.212(a)(1): One or more methods of machine guarding was not provided to protect the operator and other employees in the machine area from hazards such as those created by point of operation, ingoing nip points, rotating parts, flying chips and sparks: On or about 5/12/2017, the employer failed to ensure that the dryer rollers were effectively guarded. No guarding was installed.
Recent events (2)
- · I (S) $0
- · Z (S) $8873
More inspections in this industry (NAICS 322299)
More inspections in OH
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 342319100.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.