GERMANTOWN, WI —
OSHA Inspection: AUTOMATED MANUFACTURING, INC.
Federal Agency inspection · Safety discipline
At a glance
On , OSHA opened a federal Agency safety inspection of AUTOMATED MANUFACTURING, INC. in N115W19280 EDISON DRIVE, GERMANTOWN, WI 53022 (NAICS 332710). OSHA activity number 342810843.
OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- AUTOMATED MANUFACTURING, INC.
- Site address
- N115W19280 EDISON DRIVE
- City
- GERMANTOWN
- State
- WI
- ZIP
- 53022
- Mailing
- N115W19280 EDISON DRIVE, GERMANTOWN, WI 53022
What kind of inspection was it?
- Inspection type
- Federal Agency (M)
- Scope
- Complete (A)
- Discipline
- Safety
- Advance notice
- No
- Union status
- B
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 332710
- Employees
- 14
- Ownership type
- A
Citations
6 citations on file for this inspection.
1910.215 A01
- Issued
- May 31, 2018
- Penalty
- Initial $2,218 · Current $1,000 Reduced
General-duty citation text
29 CFR 1910.215(a)(1): Abrasive wheel(s) used on grinding machinery were not used with safety guard(s). (a) Employees performed offhand grinding work on the eight (8) inch MasterForce bench grinder without a tongue guard, exposing employees to a struck by hazard. (a) Employees performed offhand grinding work on the eight (8) inch United States Electrical Tool Co. bench grinder without a tongue guard, exposing employees to a struck by hazard.
Recent events (2)
- — I (S) $1000
- — Z (S) $2218
1910.215 A04
- Issued
- May 31, 2018
- Penalty
- Initial $2,218 · Current $1,000 Reduced
General-duty citation text
29 CFR 1910.215(a)(4): Work rest(s) on grinding machinery were not adjusted closely to the wheel with a maximum opening of one eighth inch: (a) Employees performed offhand grinding work on the eight (8) inch MasterForce bench grinder without a work rest, exposing employees to a struck by hazard. (b) Employees performed offhand grinding work on the eight (8) inch United States Electrical Tool Co. bench grinder without a work rest, exposing employees to a struck by hazard.
Recent events (2)
- — I (S) $1000
- — Z (S) $2218
1910.303 B01
- Issued
- May 31, 2018
- Penalty
- Initial $3,696 · Current $1,000 Reduced
General-duty citation text
29 CFR 1910.303(b)(1): Electrical equipment was not free from recognized hazards that were likely to cause death or serious physical harm to employees: (a) Mitsubishi Electrical Discharge Machine (Type DWC-200): On or about December 6, 2017, employees were exposed to an electrical shock hazard while working on and around the machine. The flexible metal conduit (FMC) was pulled away from the machine electrical connection fitting, exposing live electrical wires and electrical wiring were improperly spliced together.
Recent events (2)
- — I (S) $1000
- — Z (S) $3696
1910.303 G01
- Issued
- May 31, 2018
- Penalty
- Initial $3,696 · Current $1,000 Reduced
General-duty citation text
29 CFR 1910.303(g)(1): Sufficient access and working space was not provided and maintained about all electric equipment (operating at 600 volts, nominal, or less to ground) to permit ready and safe operation and maintenance of such equipment. (a) Electrical panels located in the middle of the shop were blocked. (b) Electrical panels located in the back of the shop were blocked.
Recent events (2)
- — I (S) $1000
- — Z (S) $3696
1910.212 A01
- Issued
- May 31, 2018
- Abate by
- Jun 12, 2018
- Penalty
- Initial $44,342 · Current $21,000 Reduced
General-duty citation text
29 CFR 1910.212(a)(1): One or more methods of machine guarding was not provided to protect the operator and other employees in the machine area from hazards such as those created by point of operation, ingoing nip points, rotating parts, flying chips and sparks: (a) On or about December 5, 2017, the safety interlocks were bypassed on the Leadwell CNC machine (Model No. LTC-25AM and Serial No. L2TAB0605) which exposed employees to an entanglement hazard. (b) On or about December 5, 2017, the safety interlocks were bypassed on the Daewoo Puma CNC machine (Model No. 240MA and Serial No. P24M0065) which exposed employees to an entanglement hazard.
Recent events (2)
- — I (W) $21000
- — Z (W) $44342
1910.179 L03 III D
- Issued
- May 31, 2018
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.179(l)(3)(iii)(d): Pendant control stations were not kept clean, and/or their function labels were not kept legible: (a) Pendant controls on the Coffing (Model JLC) over head craned were not legible, which exposed employees to a crushing and struck by hazard.
Recent events (2)
- — I (O) $0
- — Z (O) $0
More inspections at Automated Manufacturing, INC.
View Automated Manufacturing, INC.'s full OSHA safety record →
More inspections in this industry (NAICS 332710)
More inspections in WI
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 342810843.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.