ROCHESTER, NY —
OSHA Inspection: IEC ELECTRONICS CORP.
Referral inspection · Safety discipline
At a glance
On , OSHA opened a referral safety inspection of IEC ELECTRONICS CORP. in 1365 EMERSON STREET, ROCHESTER, NY 14606 (NAICS 333518). OSHA activity number 342828506.
OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- IEC ELECTRONICS CORP.
- Site address
- 1365 EMERSON STREET
- City
- ROCHESTER
- State
- NY
- ZIP
- 14606
- Mailing
- 1365 EMERSON STREET, ROCHESTER, NY 14606
What kind of inspection was it?
- Inspection type
- Referral (C)
- Scope
- Partial (B)
- Discipline
- Safety
- Advance notice
- No
- Union status
- B
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 333518
- Employees
- 45
- Ownership type
- A
Citations
2 citations on file for this inspection.
1910.147 C04 I
- Issued
- Feb 28, 2018
- Abate by
- Apr 20, 2018
- Penalty
- Initial $9,239 · Current $5,000 Reduced
General-duty citation text
29 CFR 1910.147(c)(4)(i): Procedures were not developed and utilized for the control of potentially hazardous energy when employees were engaged in activities covered by this section: a) On or about 12/15/17 in the Fabrication areas; employees were exposed to an amputation hazard during removing and installing tooling and dies on the power presses when they used the emergency stop button or the stop button instead of shutting off the disconnect and applying an energy control device. ABATEMENT CERTIFICATION REQUIRED
Recent events (2)
- — I (S) $5000
- — Z (S) $9239
1910.212 A03 II
- Issued
- Feb 28, 2018
- Abate by
- Apr 20, 2018
- Penalty
- Initial $12,934 · Current $8,400 Reduced
General-duty citation text
29 CFR 1910.212(a)(3)(ii): Point(s) of operation of machinery were not guarded to prevent employee(s) from having any part of their body in the danger zone(s) during operating cycle(s): a) On or about 12/11/17 in the Fabrication 2nd Bay; employees were exposed to an amputation hazard when the point of operation on the #4 Amada brand press brake was not guarded. While producing a part which required periodic manual adjustments of a piece of Mylar, plastic covered the die to eliminate visible tooling marks on the part, the press brake operator was required to place their fingers in or near the point of operation. b) On or about 12/15/17 in the Fabrication area; employees were exposed to an amputation hazard when the dual palm buttons on the Daicro press brake were not functioning and the treadle was not guarded. c) On or about 12/15/17 in the Fabrication area; employees were exposed to an amputation hazard when the cover on the foot pedal for the Niagara HBM-135 and HB-55 was wrapped in the open position by a length of metal wire or tape. ABATEMENT DOCUMENTATION REQUIRED
Recent events (2)
- — I (S) $8400
- — Z (S) $12934
More inspections at IEC Electronics Corp.
View IEC Electronics Corp.'s full OSHA safety record →
More inspections in this industry (NAICS 333518)
More inspections in NY
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 342828506.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.