ALLENTOWN, PA ·
OSHA Inspection: BRITTON SERVICES, INC.
Fatality or catastrophe inspection · Safety discipline
At a glance
On , OSHA opened a fatality or catastrophe safety inspection of BRITTON SERVICES, INC. in 101 N. 6TH ST., ALLENTOWN, PA 18102 (NAICS 811310). OSHA activity number 343195624.
OSHA opens inspections for many reasons: routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- BRITTON SERVICES, INC.
- Site address
- 101 N. 6TH ST.
- City
- ALLENTOWN
- State
- PA
- ZIP
- 18102
- Mailing
- 1800 W CHRYSLER DR, BELVIDERE, IL 61008
What kind of inspection was it?
- Inspection type
- Fatality or catastrophe (M)
- Scope
- Partial (B)
- Discipline
- Safety
- Advance notice
- No
- Union status
- Non-union (B)
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 811310
- Employees
- 4
- Ownership type
- Private (A)
Citations
6 citations on file for this inspection.
5(a)(1)
- Issued
- Nov 16, 2018
- Abate by
- Dec 31, 2018
- Penalty
- Initial $12,934 · Current $7,113 Reduced
General-duty citation text
OSH ACT of 1970 Section (5)(a)(1): Section 5(a)(1) of the Occupational Safety and Health Act of 1970: The employer did not furnish employment and a place of employment which were free from recognized hazards that were causing or likely to cause death or serious physical harm to employees in that employees were exposed to struck-by and crushed-by hazards: a) Morning Call Press Room, Allentown PA - On or about May 29, 2018, Employees moving a Goss Metroliner newspaper press used swivel bolts that were not correctly rated, sized, and torqued, to suspend the press from a crane. Among other means, feasible abatement would include, but not be limited to: 1) Comply with all provisions of ASME B30.26-2015, Rigging Hardware, Safety Standard for Cableways, Cranes, Derricks, Hoists, Hooks, Jacks, and Slings, Chapter 26-2. 2) Ensure all employees have been trained in all provisions required by ASME B30.26-2015, Rigging Hardware, Chapter 26-2, Section 26-2.7. 3) Develop and implement procedures to ensure employees have all necessary information, documentation, tools, and equipment to fully comply with the provisions of ASME B30.26-2015, Rigging Hardware, Chapter 26-2, Section 26-2.9 Operating Practices, including but not limited to Paragraph 26-2.9.1 - Adjustable Hardware Selection, and 26-2.9.4 - Rigging Practices. 4) Develop and implement procedures and documentation to ensure equipment needs are fully evaluated, inventory is checked prior to commencement of the job, all necessary manufacturer documentation is available, and equipment is stored in a clean and orderly manner to facilitate proper selection and inspection for serviceability.
Recent events (2)
- · I (S) $7113
- · Z (S) $12934
1910.28 B01 I
- Issued
- Nov 16, 2018
- Penalty
- Initial $3,696 · Current $3,696
General-duty citation text
29 CFR 1910.28(b)(1)(i): Except as provided elsewhere in this section, the employer did not ensure that each employee on a walking-working surface with an unprotected side or edge that is 4 feet (1.2 m) or more above a lower level is protected from falling by one or more of the following: (A) Guardrail systems; (B) Safety net systems; or (C) Personal fall protection systems, such as personal fall arrest, travel restraint, or positioning systems: a) Morning Call press room, 2nd floor - On or about May 29, 2018, employees walked and worked in close proximity to an unprotected edge where an overhead door was kept open, exposing them to a fall hazard greater than 10 feet that could cause serious injury.
Recent events (2)
- · I (S) $3696
- · Z (S) $3696
1910.243 C04
- Issued
- Nov 16, 2018
- Abate by
- Dec 31, 2018
- Penalty
- Initial $2,217 · Current $2,217
General-duty citation text
29 CFR 1910.243(c)(4): Other portable grinders. The maximum angular exposure of the grinding wheel periphery and sides for safety guards used on other portable grinding machines shall not exceed 180 deg. and the top half of the wheel shall be enclosed at all times. a) Morning Call press room - On or about May 29, 2018, Employees used portable hand held DeWalt angle grinders with the guards removed during press removal operations.
Recent events (2)
- · I (S) $2217
- · Z (S) $2217
1910.305 G02 II
- Issued
- Nov 16, 2018
- Penalty
- Initial $2,217 · Current $2,217
General-duty citation text
29 CFR 1910.305(g)(2)(ii): Flexible cords were not used only in continuous lengths without splice or tap: a) Morning Call press room - On or about May 29, 2018, Employees used extension cords that had been spliced and taped to power portable hand tools.
Recent events (2)
- · I (S) $2217
- · Z (S) $2217
1910.1200 G01
- Issued
- Nov 16, 2018
- Abate by
- Dec 6, 2018
- Penalty
- Initial $2,217 · Current $2,217
9000
General-duty citation text
29 CFR 1910.1200(g)(1): Employers did not have a safety data sheet in the workplace for each hazardous chemical which they use a) Morning Call press room - On or about May 29, 2018, The employer did not have a safety data sheet in the workplace for employees who were exposed to potential inhalation hazards of crystalline silica.
Recent events (2)
- · I (S) $2217
- · Z (S) $2217
1910.1200 H01
- Issued
- Nov 16, 2018
- Abate by
- Dec 6, 2018
- Penalty
- Initial $0 · Current $0
9000
General-duty citation text
29 CFR 1910.1200(h)(1): Employees were not provided effective information and training on hazardous chemicals in their work area at the time of their initial assignment and whenever a new hazard that the employees had not been previously trained about was introduced into their work area: a) Morning Call press room - On or about May 29, 2018, The employer had not provided required Hazard Communication training to employees who were exposed to potential inhalation hazards of crystalline silica and other chemicals in the workplace.
Recent events (2)
- · I (S) $0
- · Z (S) $0
More inspections in this industry (NAICS 811310)
More inspections in PA
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). OSHA publishes its own view of this case as inspection number 343195624.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.