OSHA Inspection: RIVERWOOD CABINS LLC

Issued

Sep 18, 2018

Abate by

Sep 26, 2018

Penalty

Initial $5,174 · Current $3,881 Reduced

General-duty citation text

29 CFR 1910.28(b)(1)(i): The employer did not ensure that each employee on a walking-working surface with an unprotected side or edge that is 4 feet (1.2m) or more above a lower level was protected from falling by guardrail systems, safety net system, or personal fall arrest system.   a) 3700 Rte14, Himrod, NY, On or about 6/13/18: Employees were installing prefab roofing and other structural components that contained a fall distance of at least 8 Feet 6 inches without using fall protection.

Issued

Sep 18, 2018

Abate by

Oct 1, 2018

Penalty

Initial $5,174 · Current $3,881 Reduced

General-duty citation text

29 CFR 1910.147(c)(1): The employer did not establish a program consisting of an energy control procedure, employee training and periodic inspections to ensure that before any employee performed any servicing or maintenance on a machine or equipment where the unexpected energizing, startup or release of stored energy could occur and cause injury, the machine or equipment shall be isolated from the energy source and rendered inoperative.  a) 3700 Rte 14, Himrod, NY 14842, On or about6/13/18: Untrained maintenance personnel perform  electrical work with out having a LOTO program in place.

Issued

Sep 18, 2018

Abate by

Oct 1, 2018

Penalty

Initial $3,880 · Current $2,910 Reduced

General-duty citation text

29 CFR 1910.178(l)(4)(iii): An evaluation of each powered industrial truck operator's performance was not being conducted at least once every three years.  a) 3700 Rte 14, Himrod, NY 14842., On or about 6/13/18: Employees operating forktrucks were not evaluated for performance at least once every three years.

Issued

Sep 18, 2018

Abate by

Sep 26, 2018

Penalty

Initial $6,467 · Current $4,850 Reduced

General-duty citation text

29 CFR 1910.213(d)(1): Circular handfed crosscut table saw(s) were not guarded by an automatically adjusting hood which completely enclosed that portion of the saw above the table and above the material being cut.  a) 3700 Rte 14, Himrod, NY, On or about 6/13/18: A General table saw was missing a proper adjustable hood guard when employees were performing crosscut operations.

Issued

Sep 18, 2018

Abate by

Sep 26, 2018

Penalty

Initial $0 · Current $0

General-duty citation text

29 CFR 1910.219(c)(2)(i): All exposed part(s) of horizontal shafting seven (7) feet or less from floor or working platform were not protected by stationary casing(s) enclosing shafting completely or by trough(s) enclosing sides and top or sides and bottom of shafting.   a) 3700 Rte 14, Himrod, NY, 14842, On or 6/13/18: The Tenoning machine had an exposed spinning shaft when in operation.

Issued

Sep 18, 2018

Abate by

Sep 26, 2018

Penalty

Initial $0 · Current $0

General-duty citation text

29 CFR 1910.305(g)(2)(ii): Flexible cords were not used only in continuous lengths without splice or tap.  a) 3700 Rte 14, Himrod, NY, On or about 6/13/18:  A yellow extension that supplied power to a Dewalt chop saw contained a splice.

Issued

Sep 18, 2018

Abate by

Sep 26, 2018

Penalty

Initial $0 · Current $0

General-duty citation text

29 CFR 1910.334(a)(2)(i): Portable cord and plug connected equipment and flexible cord sets (extension cords) were not visually inspected before use on any shift for external defects (such as loose parts, deformed and missing pins, or damage to outer jacket or insulation) and for evidence of possible internal damage (such as pinched or crushed outer jacket).   a) 3700 Rte 14, Himrod, NY 14842,  On or about 6/13/18: A Bosch jigsaw had a damaged strain relief on its power cord.

Issued

Sep 18, 2018

Abate by

Oct 1, 2018

Penalty

Initial $0 · Current $0

General-duty citation text

29 CFR 1910.1200(e)(1): The employer did not develop, implement, and/or maintain at the workplace a written hazard communication program which describes how the criteria specified in 29 CFR 1910.1200(f), (g), and (h) will be met:     a)3700 Rte 14, Himrod, NY 14842, On or about 6/13/18:  Employees were exposed to hazardous adhesives, glues and paints without having a proper Hazard Communication plan in place.