GALVESTON, TX —
OSHA Inspection: ALEJANDRO LARIOS
Planned inspection · Safety discipline
At a glance
On , OSHA opened a planned safety inspection of ALEJANDRO LARIOS in 2113 SEALY AVE CORNER OF SEALY AND 21ST STREET, GALVESTON, TX 77550 (NAICS 238130). OSHA activity number 343316725.
OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- ALEJANDRO LARIOS
- Site address
- 2113 SEALY AVE CORNER OF SEALY AND 21ST STREET
- City
- GALVESTON
- State
- TX
- ZIP
- 77550
- Mailing
- 215 BAILEY BROOK LANE, DICKINSON, TX 77539
What kind of inspection was it?
- Inspection type
- Planned (H)
- Scope
- Complete (A)
- Discipline
- Safety
- Advance notice
- No
- Union status
- B
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 238130
- Employees
- 3
- Ownership type
- A
Citations
6 citations on file for this inspection.
1926.102 A01
- Issued
- Jul 31, 2018
- Penalty
- Initial $2,217 · Current $2,217
General-duty citation text
29 CFR 1926.102(a)(1): Employees were not provided with eye and face protective equipment when machines or operations presented potential eye or face injury from physical, chemical, or radiation agents: a) At the construction side, employees were not provided with eye protection when connecting joints with a pneumatic nail gun.
Recent events (1)
- — Z (S) $2217
1926.304 D
- Issued
- Jul 31, 2018
- Penalty
- Initial $2,217 · Current $2,217
General-duty citation text
29 CFR 1926.304(d): Portable, power-driven circular saw(s) were not equipped with a guard above and below the base plate or shoe: a) At the construction site, a Makita 5007F Circular Saw (Serial number #1962801) was not guarded. b) At the construction site, a Makita 5007F Circular Saw (Unknown Serial number) was not guarded.
Recent events (1)
- — Z (S) $2217
1926.501 B13
- Issued
- Jul 31, 2018
- Abate by
- Aug 13, 2018
- Penalty
- Initial $2,217 · Current $2,217
General-duty citation text
29 CFR 1926.501(b)(13): Each employee(s) engaged in residential construction activities 6 feet (1.8 m) or more above lower levels were not protected by guardrail systems, safety net system, or personal fall arrest system, nor were employee(s) provided with an alternative fall protection measure under another provision of paragraph 1926.501 (b): a) At the construction site, employees were working approximately 10.5 feet above the unpaved ground without any type of a fall protection system.
Recent events (1)
- — Z (S) $2217
1926.503 A01
- Issued
- Jul 31, 2018
- Abate by
- Aug 24, 2018
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1926.503(a)(1): The employer did not provide a training program for each employee potentially exposed to fall hazards to enable each employee to recognize the hazards of falling and the procedures to be followed in order to minimize these hazards: a) At the construction site, employees working approximately 10.5 feet above the unpaved ground, had not been trained on the recognition of fall hazards and the procedures to be followed to minimize those hazards.
Recent events (1)
- — Z (S) $0
1926.1053 B01
- Issued
- Jul 31, 2018
- Abate by
- Aug 13, 2018
- Penalty
- Initial $1,663 · Current $1,663
General-duty citation text
29 CFR 1926.1053(b)(1): Portable ladders were used for access to an upper landing surface and the ladder side rails did not extend at least 3 feet (.9 m) above the upper landing surface to which the ladder was used to gain access: a) At the construction site, employees were exposed to fall hazards when using a ladder that was less than 3 feet above the upper landing surface while gaining access to the top plates.
Recent events (1)
- — Z (S) $1663
1926.405 G02 IV
- Issued
- Jul 31, 2018
- Abate by
- Aug 13, 2018
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1926.405(g)(2)(iv): Flexible cords were not connected to devices and fittings so that strain relief is provided to prevent pull from being directly transmitted to joints or terminal screws: a) At the construction site, the Makita 5007F Circular Saw flexible cord lacked strain relief.
Recent events (1)
- — Z (O) $0
More inspections at Alejandro Larios
View Alejandro Larios's full OSHA safety record →
More inspections in this industry (NAICS 238130)
More inspections in TX
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 343316725.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.