MIDLAND, TX —
OSHA Inspection: SUNRISE SHEET METAL FABRICATION HEATING & AIR CONDITIONING
Planned inspection · Safety discipline
At a glance
On , OSHA opened a planned safety inspection of SUNRISE SHEET METAL FABRICATION HEATING & AIR CONDITIONING in 3207 W. INDUSTRIAL AVE., MIDLAND, TX 79701 (NAICS 332312). OSHA activity number 343484846.
OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Site address
- 3207 W. INDUSTRIAL AVE.
- City
- MIDLAND
- State
- TX
- ZIP
- 79701
- Mailing
- 3207 W. INDUSTRIAL AVE., MIDLAND, TX 79701
What kind of inspection was it?
- Inspection type
- Planned (H)
- Scope
- Complete (A)
- Discipline
- Safety
- Advance notice
- No
- Union status
- B
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 332312
- Employees
- 6
- Ownership type
- A
Citations
7 citations on file for this inspection.
1910.178 L01 II
- Issued
- Mar 12, 2019
- Abate by
- Apr 5, 2019
- Penalty
- Initial $2,273 · Current $1,364 Reduced
General-duty citation text
29 CFR 1910.178(l)(1)(ii): The employer did not ensure that each operator had successfully completed the training required by paragraph (l), except as permitted by paragraph (l)(5), prior to permitting an employee to operate a a) At the facility, where the operators of powered industrial trucks have not received training prior to operations, exposing employees to struck-by and caught-in-between hazards.
Recent events (2)
- — I (S) $1363.8
- — Z (S) $2273
1910.254 D09 III
- Issued
- Mar 12, 2019
- Abate by
- Apr 5, 2019
- Penalty
- Initial $3,410 · Current $2,046 Reduced
General-duty citation text
29 CFR 1910.254(d)(9)(iii): Cables with damaged insulation or exposed bare conductors were not replace: a) At the facility, the lead cables on the Miller Welder, serial number LB119560, were damaged and covered in black tape.
Recent events (2)
- — I (S) $2046
- — Z (S) $3410
1910.334 A02 II
- Issued
- Mar 12, 2019
- Abate by
- Apr 5, 2019
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.334(a)(2)(ii): There was a defect or evidence of damage that could have exposed an employee to injury and the defective or damaged item was not removed from service: a) At the facility, the flexible cord on the Sears Craftsman Grinder was frayed, wrapped in black tape, and not removed from service, exposing employees to electrical hazards. b) At the facility, the flexible cord on the Hitachi grinder was frayed, wrapped in black tape, and not removed from service, exposing employees to electrical hazards.
Recent events (2)
- — I (S) $0
- — Z (S) $0
1910.305 G02 III
- Issued
- Mar 12, 2019
- Abate by
- Apr 5, 2019
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.305(g)(2)(iii): Flexible cords and cables were not connected to devices and fittings so that strain relief was provided that would prevent pull from being directly transmitted to joints or terminal screws: a) at the facility, the flexible cord on the Sears Craftsman grinder lacked strain relief, exposing the inner conductors.
Recent events (2)
- — I (S) $0
- — Z (S) $0
1910.334 A03 I
- Issued
- Mar 12, 2019
- Abate by
- Apr 5, 2019
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.334(a)(3)(i): A flexible cord used with grounding type equipment did not contain an equipment grounding conductor: a) at the facility, an orange extension cord powering the Hitachi disc grinder was missing its grounding prong. b) at the facility, an orange extension cord powering the Sears Craftsman grinder was missing its grounding prong.
Recent events (2)
- — I (S) $0
- — Z (S) $0
1910.303 F02
- Issued
- Mar 12, 2019
- Abate by
- Apr 5, 2019
- Penalty
- Initial $2,273 · Current $1,364 Reduced
General-duty citation text
29 CFR 1910.303(f)(2): Each service, feeder, and branch circuit, at its disconnecting means or overcurrent device, was not legibly marked to indicate its purpose, nor located and arranged so the purpose was evident: a) At the facility, where breakers within a circuit breaker box in the corner of the shop were not labeled.
Recent events (2)
- — I (S) $1363.8
- — Z (S) $2273
1910.37 B02
- Issued
- Mar 12, 2019
- Abate by
- Apr 5, 2019
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.37(b)(2): Each exit was not clearly visible and marked by a sign reading "Exit": a) At the facility, North exit door to shop was not clearly and visibly marked by a sign reading "Exit."
Recent events (2)
- — I (O) $0
- — Z (O) $0
More inspections at Sunrise Sheet Metal Fabrication Heating & AIR Conditioning
View Sunrise Sheet Metal Fabrication Heating & AIR Conditioning's full OSHA safety record →
More inspections in this industry (NAICS 332312)
More inspections in TX
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 343484846.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.