BAYTOWN, TX —
OSHA Inspection: JINDAL SAW USA, LLC
Federal Agency inspection · Safety discipline
At a glance
On , OSHA opened a federal Agency safety inspection of JINDAL SAW USA, LLC in 1411 SOUTH FM 565, BAYTOWN, TX 77523 (NAICS 332996). OSHA activity number 343647103.
OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- JINDAL SAW USA, LLC
- Site address
- 1411 SOUTH FM 565
- City
- BAYTOWN
- State
- TX
- ZIP
- 77523
- Mailing
- 1411 SOUTH FM 565, BAYTOWN, TX 77523
What kind of inspection was it?
- Inspection type
- Federal Agency (M)
- Scope
- Complete (A)
- Discipline
- Safety
- Advance notice
- No
- Union status
- B
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 332996
- Employees
- 8
- Ownership type
- A
Citations
5 citations on file for this inspection.
1910.28 B03 IV
- Issued
- Jun 3, 2019
- Penalty
- Initial $5,683 · Current $4,263 Reduced
General-duty citation text
29 CFR 1910.28(b)(3)(iv): Each employee was not protected from falling into a ladderway floor hole or ladderway platform hole by a guardrail system and toeboards erected on all exposed sides, except at the entrance to the hole, where a self-closing gate or an offset must be used: a) At the cooling and quench tanks, the ladderway floor holes were inadvertently and temporarily not covered or protected by a guardrail system, an offset, or a self-closing gate.
Recent events (2)
- — I (O) $4263
- — Z (S) $5683
1910.147 C04 I
- Issued
- Jun 3, 2019
- Abate by
- Jul 8, 2019
- Penalty
- Initial $13,260 · Current $9,945 Reduced
General-duty citation text
29 CFR 1910.147(c)(4)(i): Procedures were not developed, documented and utilized for the control of potentially hazardous energy when employees were engaged in activities covered by this section: a) In the Forge Shop, where the energy control procedures were not utilized for the control of potentially hazardous energy on the HT Furnace were inadvertently improperly utilized during maintenance activities.
Recent events (2)
- — I (S) $9945
- — Z (S) $13260
1910.147 D02
- Issued
- Jun 3, 2019
- Abate by
- Jul 19, 2019
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.147(d)(2): The machine or equipment was not turned off or shut down using the procedures established for the machine or equipment: a) In the Forge Shop, where the written procedures established by the employer for turning off or shutting down the HT Furnace were inadvertently not followed.
Recent events (2)
- — I (S) $0
- — Z (S) $0
1910.147 C04 II B
- Issued
- Jun 3, 2019
- Abate by
- Jul 8, 2019
- Penalty
- Initial $13,260 · Current $9,945 Reduced
General-duty citation text
29 CFR 1910.147(c)(4)(ii)(B): The energy control procedures did not clearly and specifically outline the steps for shutting down, isolating, blocking and securing machines or equipment to control hazardous energy: a) In the Forge Shop, where written energy control procedures for components of the HT Furnace inadvertently failed to clearly outline all of the steps to be utilized for the control of hazardous energy.
Recent events (2)
- — I (S) $9945
- — Z (S) $13260
1910.147 C07 III A
- Issued
- Jun 3, 2019
- Abate by
- Jul 8, 2019
- Penalty
- Initial $13,260 · Current $9,945 Reduced
General-duty citation text
29 CFR 1910.147(c)(7)(iii)(A): Retraining was not provided for authorized and affected employees when there was a change in their job assignments, a change in machines, equipment or processes that presented a new hazard, or when there was a change in the energy control procedures: a) In the Forge Shop, where an affected employee from the coatings department had inadvertently not been retrained when assigned to operate the HT Furnace.
Recent events (2)
- — I (S) $9945
- — Z (S) $13260
More inspections at Jindal SAW USA, LLC
View Jindal SAW USA, LLC's full OSHA safety record →
More inspections in this industry (NAICS 332996)
More inspections in TX
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 343647103.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.