KEWANEE, IL ·
OSHA Inspection: ELM STREET INDUSTRIES, INC.
Planned inspection · Safety discipline
At a glance
On , OSHA opened a planned safety inspection of ELM STREET INDUSTRIES, INC. in 206 W. 4TH ST., KEWANEE, IL 61443 (NAICS 321920). OSHA activity number 343839635.
OSHA opens inspections for many reasons: routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- ELM STREET INDUSTRIES, INC.
- Site address
- 206 W. 4TH ST.
- City
- KEWANEE
- State
- IL
- ZIP
- 61443
- Mailing
- 1310 ELM PLACE, KELSO, WA 98626
What kind of inspection was it?
- Inspection type
- Planned (H)
- Scope
- Complete (A)
- Discipline
- Safety
- Advance notice
- No
- Union status
- B
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 321920
- Employees
- 3
- Ownership type
- A
Citations
5 citations on file for this inspection.
1910.36 D01
- Issued
- Jun 11, 2019
- Abate by
- Jul 3, 2019
- Penalty
- Initial $3,334 · Current $2,000 Reduced
General-duty citation text
29 CFR 1910.36(d)(1): Employees were not able to open an exit route door from the inside at all times without keys, tools, or special knowledge: On or about March 11, 2019, Employees working were exposed to fire, smoke inhalation, slips, trips and falls hazards in the event of an emergency because the emergency had a padlocked, deadbolt and bungee cords.
Recent events (2)
- · I (S) $2000.4
- · Z (S) $3334
1910.147 C01
- Issued
- Jun 11, 2019
- Abate by
- Jul 3, 2019
- Penalty
- Initial $4,168 · Current $2,501 Reduced
General-duty citation text
29 CFR 1910.147(c)(1): The employer did not establish a program consisting of an energy control procedure, employee training and periodic inspections to ensure that before any employee performed any servicing or maintenance on a machine or equipment where the unexpected energizing, startup or release of stored energy could occur and cause injury, the machine or equipment shall be isolated from the energy source and rendered inoperative On or about March 11, 2019, employees performing service and maintenance on equipment were exposed to caught-in and amputation hazards and the employer had not developed and implemented a comprehensive energy control program.
Recent events (2)
- · I (S) $2500.8
- · Z (S) $4168
1910.178 L04 III
- Issued
- Jun 11, 2019
- Abate by
- Jul 3, 2019
- Penalty
- Initial $3,334 · Current $2,000 Reduced
General-duty citation text
29 CFR 1910.178(l)(4)(iii): Employer did not provide an evaluation of each powered industrial trucks operators performance, at least once every three years: On or about March 11, 2019, The employer did not evaluate the performance of each previously trained and certified powered industrial truck operator at least once every three years.
Recent events (2)
- · I (O) $2000.4
- · Z (S) $3334
1910.213 D01
- Issued
- Jun 11, 2019
- Abate by
- Jul 18, 2019
- Penalty
- Initial $4,168 · Current $2,501 Reduced
General-duty citation text
29 CFR 1910.213(d)(1): Circular handfed crosscut table saw(s) were not guarded by an automatically adjusting hood which completely enclosed that portion of the saw above the table and above the material being cut: On or about March 11, 2019, Employees operating the table saw were exposed to amputation hazards because the table saw did not have an effective guard. The guard had broken pieces, duct tape, and a black zip tie was holding the guard in place.
Recent events (2)
- · I (S) $2500.6
- · Z (S) $4168
1910.213 H01
- Issued
- Jun 11, 2019
- Abate by
- Jul 18, 2019
- Penalty
- Initial $4,168 · Current $2,501 Reduced
General-duty citation text
29 CFR 1910.213(h)(1): The sides of the lower exposed portion of the blade of radial saw(s) were not guarded to the full diameter of the blade by a device that automatically adjusted itself to the thickness of the stock and remained in contact with the stock being cut: On or about March 11, 2019, Employees operating the table saw were exposed to amputation hazards because the radial saw did not have an effective guard. The guard had a black zip tie holding the guard in place, exposing a portion of the blade.
Recent events (2)
- · I (S) $2500.8
- · Z (S) $4168
More inspections in this industry (NAICS 321920)
More inspections in IL
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 343839635.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.