SCOTTSBLUFF, NE —
OSHA Inspection: PANHANDLE CONCRETE PRODUCTS, INC.
Planned inspection · Safety discipline
At a glance
On , OSHA opened a planned safety inspection of PANHANDLE CONCRETE PRODUCTS, INC. in 2202 W OVERLAND, SCOTTSBLUFF, NE 69361 (NAICS 327390). OSHA activity number 344115233.
OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- PANHANDLE CONCRETE PRODUCTS, INC.
- Site address
- 2202 W OVERLAND
- City
- SCOTTSBLUFF
- State
- NE
- ZIP
- 69361
- Mailing
- PO BOX 209, SCOTTSBLUFF, NE 69363
What kind of inspection was it?
- Inspection type
- Planned (H)
- Scope
- Complete (A)
- Discipline
- Safety
- Advance notice
- No
- Union status
- B
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 327390
- Employees
- 19
- Ownership type
- A
Citations
5 citations on file for this inspection.
1910.147 C04 II
- Issued
- Sep 30, 2019
- Abate by
- Nov 18, 2019
- Penalty
- Initial $2,898 · Current $2,029 Reduced
General-duty citation text
29 CFR 1910.147(c)(4)(ii): The energy control procedures did not clearly and specifically outline the scope, purpose, authorization, rules, and techniques to be utilized for the control of hazardous energy, including, but not limited to the items of this section: The employer is failing ensure that employees are protected from electrical hazards. This was most recently documented at 2202 West Overland, Scottsbluff, Nebraska 69361 on June 27, 2019. The employer failed to ensure that the lockout procedures used by employees to service equipment were specific for locking out equipment, including, but not limited to, but not limited to, the overhead crane, and the Pipe Machine.
Recent events (2)
- — I (S) $2028.6
- — Z (S) $2898
1910.178 L04 III
- Issued
- Sep 30, 2019
- Abate by
- Nov 18, 2019
- Penalty
- Initial $2,319 · Current $1,623 Reduced
General-duty citation text
29 CFR 1910.178(l)(4)(iii): An evaluation of each powered industrial truck operators performance shall be conducted at least once every three years: The employer is failing to protect employees from struck-by hazards. This violation was most recently documented at a worksite located at or near 2202 West Overland, Scottsbluff, Nebraska 69361 on June 27, 2019. The employer did not ensure that an operators performances were being evaluated at least once every three years when operating a forklift.
Recent events (2)
- — I (S) $1623.3
- — Z (S) $2319
1910.215 B09
- Issued
- Sep 30, 2019
- Penalty
- Initial $2,319 · Current $1,623 Reduced
General-duty citation text
29 CFR 1910.215(b)(9): The distance between the abrasive wheel periphery(s) and the adjustable tongue or the end of the safety guard peripheral member at the top exceeded one fourth inch: The employer is failing ensure that employees are protected from struck-by hazards. This was most recently documented at 2202 West Overland, Scottsbluff, Nebraska 69361 on June 27, 2019. Employees were using a 6 Atlas Bench Grinder which had the abrasive wheel periphery opening of approximately 1 inch.
Recent events (2)
- — I (S) $1623.3
- — Z (S) $2319
1910.305 G01 IV
- Issued
- Sep 30, 2019
- Penalty
- Initial $2,319 · Current $1,623 Reduced
General-duty citation text
29 CFR 1910.305(g)(1)(iv): Flexible cords and cables were used for purposes prohibited by subparagraph (D) of this paragraph where the employer did not ensure that flexible cord was not attached to a building surface: The employer is failing to protect employees from the hazard of electrical shocks. This violation was most recently documented at a worksite located at or near 2202 West Overland, Scottsbluff, Nebraska 69361 on June 27, 2019. The flexible cord was attached to a metal conduit and a metal pipe by the exit door in the Add/Mix Room.
Recent events (2)
- — I (S) $1623.3
- — Z (S) $2319
1910.147 C06 II
- Issued
- Sep 30, 2019
- Abate by
- Nov 18, 2019
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.147(c)(6)(ii): The periodic inspection certification of energy control procedures did not contain the required documentation on identification of the machine or equipment inspection date, employees included, and the person performing the inspection: The employer is failing ensure that employees are protected from the hazard of potential amputations, electrical injuries, and chemical burns from not documenting lockout reviews. This was most recently documented at 2202 West Overland, Scottsbluff, Nebraska 69361.on July 27, 2019. There was no documentation provided by the employer that showed the person performing the periodic inspection and the employees included in the inspection within the past year. The last documented periodic inspection was 2014. Abatement certification is required for this violation. The abatement certification sheet is enclosed with the citations.
Recent events (2)
- — I (O) $0
- — Z (O) $0
More inspections at Panhandle Concrete Products, INC.
View Panhandle Concrete Products, INC.'s full OSHA safety record →
More inspections in this industry (NAICS 327390)
More inspections in NE
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 344115233.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.