ROCK ISLAND, IL —
OSHA Inspection: HILL & VALLEY, INC.
Referral inspection · Safety discipline
At a glance
On , OSHA opened a referral safety inspection of HILL & VALLEY, INC. in 320 44TH STREET, ROCK ISLAND, IL 61201 (NAICS 311813). OSHA activity number 344263777.
OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- HILL & VALLEY, INC.
- Site address
- 320 44TH STREET
- City
- ROCK ISLAND
- State
- IL
- ZIP
- 61201
- Mailing
- 320 44TH STREET, ROCK ISLAND, IL 61201
What kind of inspection was it?
- Inspection type
- Referral (C)
- Scope
- Partial (B)
- Discipline
- Safety
- Advance notice
- No
- Union status
- B
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 311813
- Employees
- 230
- Ownership type
- A
Citations
3 citations on file for this inspection.
1910.147 C07 I
- Issued
- Dec 17, 2019
- Abate by
- Jan 27, 2020
- Penalty
- Initial $10,419 · Current $0 Reduced
General-duty citation text
29 CFR 1910.147(c)(7)(i): The employer did not provide training to ensure that the purpose and function of the energy control program are understood by employees and that the knowledge and skills required for the safe application, usage, and removal of the energy controls are acquired by employees: On or about August 14, 2019, an employee was exposed to hazardous energy sources when performing maintenance and servicing, including but not limited on the Angel Press Equipment, Model No. E-500SM and the employer did not provide training. a. The training shall include the following: b. Each authorized employee shall receive training in the recognition of applicable hazardous energy sources, the type and magnitude of the energy available in the workplace, and the methods and means necessary for energy isolation and control. c. Each affected employees shall be instructed in the purpose and use of the energy control procedures. All other employees who work operations are or may be in an area where energy control procedures may be utilized, shall be instructed about the procedure, and about the prohibition relating to attempts to restart or reenergize machines or equipment which are locked out or tagged out.
Recent events (2)
- — I (S) $0
- — Z (S) $10419
1910.147 D
- Issued
- Dec 17, 2019
- Abate by
- Jan 27, 2020
- Penalty
- Initial $10,419 · Current $0 Reduced
General-duty citation text
29 CFR 1910.147(d): The established procedure for the application of energy control (the lockout or tagout procedures) did not cover the actions listed in and was not done in sequence as required by 29 CFR 1910.147(d)(1)-(6): Employees who performed servicing and maintenance were not required to: (1) Know the type and magnitude of the energy, the hazards of the energy to be controlled, and the method or means to control the energy, (2) Turn off and shut down the machine, (3) Physically locate and operate energy isolating devices in such a manner as to isolate the machine or equipment from the energy source, (4) Affix lockout or tagout devices to each energy isolating device, (5) Prior to starting work on machines that have been locked out or tagged out, verify that isolation and deenergization of the machine or equipment have been accomplished. On or about August 14, 2019, an employee was exposed to hazardous energy sources when performing maintenance and servicing, including but not limited on the Angel Press Equipment, Model No. E-500SM because the employer did not did not cover the action listed in and was not done in sequence as required by 29 CFR 1910.147(d)(1)-(6).
Recent events (2)
- — I (S) $0
- — Z (S) $10419
1910.212 A03 II
- Issued
- Dec 17, 2019
- Abate by
- Apr 1, 2020
- Penalty
- Initial $10,419 · Current $7,814 Reduced
General-duty citation text
29 CFR 1910.212(a)(3)(ii): Point(s) of operation of machinery were not guarded to prevent employee(s) from having any part of their body in the danger zone(s) during operating cycle(s): The employer did not ensure the point of operation on the Angel Press Equipment, Model No. E-500SM, had effective guarding. a. On or about August 14, 2019, the operator was exposed to caught in and amputation hazards on the Angel Press machine because the point of operation did not prevent employees from having any part of their body in the danger zone during normal operations. b. On or about August 19, 2019, the Angel Press machine was in operation and the equipments point of operation was not effectively protected against unintended or inadvertent contact by operators.
Recent events (2)
- — I (S) $7814.25
- — Z (S) $10419
More inspections at Hill & Valley, INC.
View Hill & Valley, INC.'s full OSHA safety record →
More inspections in this industry (NAICS 311813)
More inspections in IL
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 344263777.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.