NEWARK, NJ —
OSHA Inspection: JOSEPH M. SANZARI INC.
Complaint inspection · Health discipline
At a glance
On , OSHA opened a complaint health inspection of JOSEPH M. SANZARI INC. in NJ TURNPIKE WESTERN SPUR BETWEEN EXITS 15W & 15E, NEWARK, NJ 07101 (NAICS 237310). OSHA activity number 344402813.
OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- JOSEPH M. SANZARI INC.
- Site address
- NJ TURNPIKE WESTERN SPUR BETWEEN EXITS 15W & 15E
- City
- NEWARK
- State
- NJ
- ZIP
- 07101
- Mailing
- 100 WEST FRANKLIN ST, HACKENSACK, NJ 07601
What kind of inspection was it?
- Inspection type
- Complaint (B)
- Scope
- Partial (B)
- Discipline
- Health
- Advance notice
- No
- Union status
- A
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 237310
- Employees
- 14
- Ownership type
- A
Citations
11 citations on file for this inspection.
1926.1153 C01
- Issued
- Feb 11, 2020
- Penalty
- Initial $13,494 · Current $10,795 Reduced
9000
General-duty citation text
29 CFR 1926.1153(c)(1): For each employee engaged in a task identified on Table 1, the employer did not fully and properly implement the engineering controls, work practices, and respiratory protection specified for the task on Table 1, unless the employer assesses and limits the exposure of the employee to respirable crystalline silica in accordance with paragraph (d) of this section: a) Worksite located at New Jersey Turnpike, Western Spur, 107 Letterman Bridge The employer did not properly implement engineering controls and respiratory protection for employees using jack hammers and compressed air during concrete spall work. The employer did not ensure that, during jackhammering, a continuous stream or spray of water or dust collection was utilized. The employer allowed employees to wear half mask, negative pressure respirators without medical evaluations and fit tests. Employees using jack hammers and compressed air were exposed to crystalline respirable silica at an 8-hour time-weighted average (TWA) of 83.2 micrograms per cubic meter (ug/m3), 78.5 ug/m3 and 71.8 micrograms per cubic meter (ug/m3), which are 1.7, 1.6 and 1.4 times the permissible exposure limit (PEL) of 50 ug/m3. Zero exposure was assumed for unsampled periods of 185 minutes, 278, and 180 minutes respectively. Violation occurred on or about 10/24/2019.
Recent events (3)
- — F (O) $10795
- — C (S) $13494
- — Z (S) $13494
1926.1153 D01
- Issued
- Feb 11, 2020
- Penalty
- Initial $13,494 · Current $10,795 Reduced
9000
General-duty citation text
29 CFR 1926.1153(d)(1): The employer did not ensure that employees were not exposed to an airborne concentration of respirable crystalline silica in excess of 50 ug/m3, calculated as an 8-hour TWA: a) Worksite located at New Jersey Turnpike, Western Spur, 107 Letterman Bridge Employees using jack hammers and compressed air were exposed to respirable crystalline silica at an 8-hour time-weighted average (TWA) of 83.2 micrograms per cubic meter (ug/m3), 78.5 ug/m3 and 71.8 micrograms per cubic meter (ug/m3), which are 1.7, 1.6 and 1.4 times the permissible exposure limit (PEL) of 50 ug/m3. Zero exposure was assumed for unsampled periods of 185 minutes, 278, and 180 minutes respectively. Violation occurred on or about 10/24/2019.
Recent events (3)
- — F (O) $10795
- — C (S) $13494
- — Z (S) $13494
1926.1153 D02 I
- Issued
- Feb 11, 2020
- Abate by
- Mar 31, 2020
- Penalty
- Initial $0 · Current $0
9000
General-duty citation text
29 CFR 1926.1153(d)(2)(i): The employer did not assess the exposure of each employee who was or may reasonably be expected to be exposed to respirable crystalline silica at or above the action level in accordance with either the performance option in paragraph (d)(2)(ii) or the scheduled monitoring option in paragraph (d)(2)(iii) of this section: a) Worksite located at New Jersey Turnpike, Western Spur, 107 Letterman Bridge The employer did not assess employee exposure to respirable crystalline silica while conducting jackhammering activities and using compressed air for cleaning. Employees using jack hammers and compressed air were exposed to crystalline respirable silica at an 8-hour time-weighted average (TWA) of 83.2 micrograms per cubic meter (ug/m3), 78.5 ug/m3 and 71.8 micrograms per cubic meter (ug/m3), which are 1.7, 1.6 and 1.4 times the permissible exposure limit (PEL) of 50 ug/m3. Zero exposure was assumed for unsampled periods of 185 minutes, 278, and 180 minutes respectively. Violation occurred on or about 10/24/2019.
Recent events (3)
- — F (O) $0
- — C (S) $0
- — Z (S) $0
1926.1153 D03 I
- Issued
- Feb 11, 2020
- Abate by
- Mar 31, 2020
- Penalty
- Initial $0 · Current $0
9000
General-duty citation text
29 CFR 1926.1153(d)(3)(i): The employer did not use engineering and work practice controls to reduce and maintain employee exposure to respirable crystalline silica to or below the PEL, unless the employer can demonstrate that such controls are not feasible: a) Worksite located at New Jersey Turnpike, Western Spur, 107 Letterman Bridge The employer did not use engineering and work practice controls for employees performing jackhammering activities and using compressed air on concrete spall work. The employer did not ensure that, during jackhammering, a continuous stream or spray of water or dust collection was utilized. Employees using jack hammers and compressed air were exposed to crystalline respirable silica at an 8-hour time-weighted average (TWA) of 83.2 micrograms per cubic meter (ug/m3), 78.5 ug/m3 and 71.8 micrograms per cubic meter (ug/m3), which are 1.7, 1.6 and 1.4 times the permissible exposure limit (PEL) of 50 ug/m3. Zero exposure was assumed for unsampled periods of 185 minutes, 278, and 180 minutes respectively. Violation occurred on or about 10/24/2019.
Recent events (3)
- — F (O) $0
- — C (S) $0
- — Z (S) $0
1926.1153 E02
- Issued
- Feb 11, 2020
- Abate by
- Mar 31, 2020
- Penalty
- Initial $13,494 · Current $10,795 Reduced
9000
General-duty citation text
29 CFR 1926.1153(e)(2): Where respirator use is required by this section, the employer did not institute a respiratory protection program in accordance with 29 CFR 1910.134: a) Worksite located at New Jersey Turnpike, Western Spur, 107 Letterman Bridge and corporate office at 100 West Franklin St, Hackensack NJ The employer did not institute the written respiratory protection program for employees required to wear respirators such as, but not limited to, North half and full face negative pressure respirators while conducting jackhammering activities and using compressed air on concrete spall work. Employees using jackhammers and compressed air were exposed to respirable crystalline silica at an 8-hour time-weighted average (TWA) of 83.2 micrograms per cubic meter (ug/m3), 78.5 ug/m3 and 71.8 micrograms per cubic meter (ug/m3), which are 1.7, 1.6 and 1.4 times the permissible exposure limit (PEL) of 50 ug/m3. Zero exposure was assumed for unsampled periods of 185 minutes, 278, and 180 minutes respectively. Violation occurred on or about 10/24/2019.
Recent events (3)
- — F (O) $10795
- — C (S) $13494
- — Z (S) $13494
1910.134 C01
- Issued
- Feb 11, 2020
- Abate by
- Mar 31, 2020
- Penalty
- Initial $0 · Current $0
9000
General-duty citation text
29 CFR 1910.134(c)(1) as referenced in 29 CFR 1926.103: A written respiratory protection program that included the provisions in 29 CFR 1910.134(c)(1)(i) - (ix) with worksite specific procedures was not established and implemented for required respirator use: a) Worksite located at New Jersey Turnpike, Western Spur, 107 Letterman Bridge and corporate office at 100 West Franklin St, Hackensack, NJ The employer did not implement the written respiratory protection program for employees required to wear respirators such as, but not limited to, North half and full face negative pressure respirators while conducting jackhammering activities and using compressed air on concrete spall work. Employees using jackhammers and compressed air were exposed to respirable crystalline silica at an 8-hour time-weighted average (TWA) of 83.2 micrograms per cubic meter (ug/m3), 78.5 ug/m3 and 71.8 micrograms per cubic meter (ug/m3), which are 1.7, 1.6 and 1.4 times the permissible exposure limit (PEL) of 50 ug/m3. Zero exposure was assumed for unsampled periods of 185 minutes, 278, and 180 minutes respectively. Violation occurred on or about 10/24/2019.
Recent events (3)
- — F (O) $0
- — C (S) $0
- — Z (S) $0
1910.134 E01
- Issued
- Feb 11, 2020
- Abate by
- Mar 31, 2020
- Penalty
- Initial $0 · Current $0
9000
General-duty citation text
29 CFR 1910.134(e)(1) as referenced in 29 CFR 1926.103: The employer did not provide a medical evaluation to determine the employee's ability to use a respirator, before the employee was fit tested or required to use the respirator in the workplace: a) Worksite located at New Jersey Turnpike, Western Spur, 107 Letterman Bridge and corporate office at 100 West Franklin St, Hackensack, NJ The employer did not provide medical evaluations for employees required to wear respirators such as, but not limited to, North half and full face, negative pressure respirators while conducting jackhammering activities and using compressed air on concrete spall work. Employees using jackhammers and compressed air were exposed to respirable crystalline silica at an 8-hour time-weighted average (TWA) of 83.2 micrograms per cubic meter (ug/m3), 78.5 ug/m3 and 71.8 micrograms per cubic meter (ug/m3), which are 1.7, 1.6 and 1.4 times the permissible exposure limit (PEL) of 50 ug/m3. Zero exposure was assumed for unsampled periods of 185 minutes, 278, and 180 minutes respectively. Violation occurred on or about 10/24/2019.
Recent events (3)
- — F (O) $0
- — C (S) $0
- — Z (S) $0
1910.134 F02
- Issued
- Feb 11, 2020
- Abate by
- Mar 31, 2020
- Penalty
- Initial $0 · Current $0
9000
General-duty citation text
29 CFR 1910.134(f)(2) as referenced in 29 CFR 1926.103: Employees using tight-fitting facepiece respirators were not fit tested prior to initial use of the respirator, whenever a different respirator facepiece (size, style, model or make) is used, and at least annually thereafter: a) Worksite located at New Jersey Turnpike, Western Spur, 107 Letterman Bridge and corporate office located at 100 nWest Franklin St, Hackensack, NJ The employer did not provide fit tests to employees required to wear respirators such as, but not limited to, North half and full face negative pressure respirators while conducting jackhammering activities and using compressed air on concrete spall work. Employees using jack hammers and compressed air were exposed to respirable crystalline silica at an 8-hour time-weighted average (TWA) of 83.2 micrograms per cubic meter (ug/m3), 78.5 ug/m3 and 71.8 micrograms per cubic meter (ug/m3), which are 1.7, 1.6 and 1.4 times the permissible exposure limit (PEL) of 50 ug/m3. Zero exposure was assumed for unsampled periods of 185 minutes, 278, and 180 minutes respectively. Violation occurred on or about 10/24/2019.
Recent events (3)
- — F (O) $0
- — C (S) $0
- — Z (S) $0
1910.134 G01 I A
- Issued
- Feb 11, 2020
- Abate by
- Mar 31, 2020
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.134(g)(1)(i)(A): Respirators with tight-fitting facepieces were worn by employees who had facial hair that came between the sealing surface of the facepiece and the face or that interfered with valve function: a) Worksite located at New Jersey Turnpike, Western Spur, 107 Letterman Bridge An employee with interfering facial hair wore a tight-fitting half mask, negative pressure respirator while conducting jackhammering activities and using compressed air on concrete spall work. Violation occurred on or about 10/24/2019.
Recent events (3)
- — F (O) $0
- — C (S) $0
- — Z (S) $0
1926.1153 G01
- Issued
- Feb 11, 2020
- Abate by
- Mar 31, 2020
- Penalty
- Initial $13,494 · Current $10,795 Reduced
9000
General-duty citation text
29 CFR 1926.1153(g)(1): The employer did not establish and implement a written exposure control plan: a) Worksite located at New Jersey Turnpike, Western Spur, 107 Letterman Bridge The employer did not implement the written exposure control plan for employees conducting jackhammering activities and using compressed air on concrete spall work and who were found to be overexposed to respirable crystalline silica. Employees using jack hammers and compressed air were exposed to respirable crystalline silica at an 8-hour time-weighted average (TWA) of 83.2 micrograms per cubic meter (ug/m3), 78.5 ug/m3 and 71.8 micrograms per cubic meter (ug/m3), which are 1.7, 1.6 and 1.4 times the permissible exposure limit (PEL) of 50 ug/m3. Zero exposure was assumed for unsampled periods of 185 minutes, 278, and 180 minutes respectively. Violation occurred on or about 10/24/2019.
Recent events (3)
- — F (O) $10795
- — C (S) $13494
- — Z (S) $13494
1926.1153 G01 I
- Issued
- Feb 11, 2020
- Abate by
- Mar 31, 2020
- Penalty
- Initial $0 · Current $0
9000
General-duty citation text
29 CFR 1926.1153(g)(1)(i): The exposure control plan did not contain a description of the tasks in the workplace that involve exposure to respirable crystalline silica: a) Worksite located at New Jersey Turnpike, Western Spur, 107 Letterman Bridge The written exposure control plan did not contain a description of the tasks to include using jackhammers and compressed air during concrete spall work. Employees using jackhammers and compressed air were exposed to respirable crystalline silica at an 8-hour time-weighted average (TWA) of 83.2 micrograms per cubic meter (ug/m3), 78.5 ug/m3 and 71.8 micrograms per cubic meter (ug/m3), which are 1.7, 1.6 and 1.4 times the permissible exposure limit (PEL) of 50 ug/m3. Zero exposure was assumed for unsampled periods of 185 minutes, 278, and 180 minutes respectively. Violation observed on or about 11/19/2019.
Recent events (3)
- — F (O) $0
- — C (S) $0
- — Z (S) $0
More inspections at Joseph M. Sanzari INC.
View Joseph M. Sanzari INC.'s full OSHA safety record →
More inspections in this industry (NAICS 237310)
More inspections in NJ
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 344402813.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.