SAN ANTONIO, TX ·
OSHA Inspection: GARCIA CUSTOM FRAMING
Planned inspection · Safety discipline
At a glance
On , OSHA opened a planned safety inspection of GARCIA CUSTOM FRAMING in 1702 DANCING EAGLE, SAN ANTONIO, TX 78258 (NAICS 238130). OSHA activity number 344535851.
OSHA opens inspections for many reasons: routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- GARCIA CUSTOM FRAMING
- Site address
- 1702 DANCING EAGLE
- City
- SAN ANTONIO
- State
- TX
- ZIP
- 78258
- Mailing
- 7159 ELUSIVE PASS, SAN ANTONIO, TX 78233
What kind of inspection was it?
- Inspection type
- Planned (H)
- Scope
- Partial (B)
- Discipline
- Safety
- Advance notice
- No
- Union status
- Non-union (B)
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 238130
- Employees
- 4
- Ownership type
- Private (A)
Citations
3 citations on file for this inspection.
1926.102 A01
- Issued
- Feb 7, 2020
- Abate by
- Feb 27, 2020
- Penalty
- Initial $2,313 · Current $0 Reduced
General-duty citation text
29 CFR 1926.102(a)(1): The employer shall ensure that each affected employee uses appropriate eye or face protection when exposed to eye or face hazards from flying particles, molten metal, liquid chemicals, acids or caustic liquids, chemical gases or vapors, or potentially injurious light radiation: a) 1702 Dancing Eagle: On or about January 02, 2020, and at times prior thereto, employees were exposed to a struck-by flying projectile hazard, while using a Complete NRH83 Pneumatic Nail Gun without eye protection. b) 1702 Dancing Eagle: On or about January 02, 2020, and at times prior thereto, employees were exposed to a struck-by flying projectile hazard, while using a DeWALT DWE575 7 1/4" Lightweight Circular Saw without eye protection.
Recent events (2)
- · I (S) $0
- · Z (S) $2313
1926.501 B13
- Issued
- Feb 7, 2020
- Penalty
- Initial $3,470 · Current $0 Reduced
General-duty citation text
29 CFR 1926.501(b)(13): Each employee(s) engaged in residential construction activities 6 feet (1.8 m) or more above lower levels were not protected by guardrail systems, safety net system, or personal fall arrest system, nor were employee(s) provided with an alternative fall protection measure under another provision of paragraph 1926.501 (b): 1702 Dancing Eagle: On or about January 2, 2020, and at times thereto, employees were exposed to a fall hazard greater than 6 feet while installing framing tie ins.
Recent events (2)
- · I (S) $0
- · Z (S) $3470
1926.503 A01
- Issued
- Feb 7, 2020
- Abate by
- Feb 27, 2020
- Penalty
- Initial $2,313 · Current $2,000 Reduced
General-duty citation text
29 CFR 1926.503(a)(1): The employer did not provide a training program for each employee potentially exposed to fall hazards to enable each employee to recognize the hazards of falling and the procedures to be followed in order to minimize these hazards: 1702 Dancing Eagle: On or about January 2, 2020, and at times therto, employees were exposed to a fall hazard greater than 6 feet, while installing tie-in framing without being trained on fall hazard recognition.
Recent events (2)
- · I (S) $2000
- · Z (S) $2313
More inspections in this industry (NAICS 238130)
More inspections in TX
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). OSHA publishes its own view of this case as inspection number 344535851.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.