MENOMONEE FALLS, WI —
OSHA Inspection: SCAN-PAC MANUFACTURING, INC.
Referral inspection · Safety discipline
At a glance
On , OSHA opened a referral safety inspection of SCAN-PAC MANUFACTURING, INC. in N84 W 13480 LEON RD, MENOMONEE FALLS, WI 53051 (NAICS 333613). OSHA activity number 344578968.
OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- SCAN-PAC MANUFACTURING, INC.
- Site address
- N84 W 13480 LEON RD
- City
- MENOMONEE FALLS
- State
- WI
- ZIP
- 53051
- Mailing
- N84 W 13480 LEON RD, MENOMONEE FALLS, WI 53051
What kind of inspection was it?
- Inspection type
- Referral (C)
- Scope
- Partial (B)
- Discipline
- Safety
- Advance notice
- No
- Union status
- B
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 333613
- Employees
- 110
- Ownership type
- A
Citations
4 citations on file for this inspection.
1910.28 B01 I
- Issued
- Apr 15, 2020
- Abate by
- May 11, 2020
- Penalty
- Initial $5,725 · Current $4,008 Reduced
General-duty citation text
29 CFR 1910.28(b)(1)(i): The employer did not ensure that each employee on a walking-working surface with an unprotected side or edge that was 4 feet (1.2 m) or more above a lower level was protected from falling by one or more of the following: (a) On or about November 20, 2019, at the worksite located N84 W13480 Leon Rd., Suite A, Menomonee Falls, WI, the employer did not ensure a complete guardrail system was implemented on top of the Erie Press 33 machine, thereby exposing workers to fall hazards. ...In the Alternative... 29 CFR 1910.28(b)(6)(i): Each employee less than 4 feet (1.2 m) above dangerous equipment was not protected from falling into or onto the dangerous equipment by a guardrail system or a travel restraint system, unless the equipment is covered or guarded to eliminate the hazard. (a) On or about November 20, 2019, at the worksite located N84 W13480 Leon Rd., Suite A, Menomonee Falls, WI, the employer did not ensure a complete guardrail system was implemented on top of the Erie Press 33 machine, thereby exposing workers to entanglement hazards and/or crushing hazards.
Recent events (2)
- — I (S) $4007.5
- — Z (S) $5725
1910.212 A01
- Issued
- Apr 15, 2020
- Abate by
- May 11, 2020
- Penalty
- Initial $9,543 · Current $6,680 Reduced
General-duty citation text
29 CFR 1910.212(a)(1): One or more methods of machine guarding was not provided to protect the operator and other employees in the machine area from hazards such as those created by point of operation, ingoing nip points, rotating parts, flying chips and sparks: (a) On or about January 24, 2020, at the worksite located at N84 W13480 Leon Rd., Suite A, Menomonee Falls, WI, the employer did not ensure light curtains were fully functional in both manual and auto mode when employees were exposed to moving machinery, thereby exposing workers to amputation injuries.
Recent events (2)
- — I (S) $6680.1
- — Z (S) $9543
1910.219 E03 I
- Issued
- Apr 15, 2020
- Abate by
- May 11, 2020
- Penalty
- Initial $9,543 · Current $6,680 Reduced
General-duty citation text
29 CFR 1910.219(e)(3)(i): Vertical or inclined belt(s) were not enclosed by guard(s) conforming to the requirements specified at 29 CFR 1910.219(m) and (o): (a) On or about January 24, 2020, at N84 W13480 Leon Rd., Ste A, Menomonee Falls, WI, the employer did not ensure a vertical belt on the loading table for the the Erie 12 foot press machine was adequately guarded, thereby exposing workers to entanglement hazards.
Recent events (2)
- — I (S) $6680.1
- — Z (S) $9543
1910.212 A02
- Issued
- Apr 15, 2020
- Abate by
- May 11, 2020
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.212(a)(2): Guard(s) on machine(s) were not affixed to the machine or secured elsewhere when attachment to the machine was not possible: (a) On or about January 24, 2020, at N84 W13480 Leon Rd., Suite A, Menomonee Falls, WI, the employer did not ensure a guard covering a chain mechanism on the Erie 12 foot press machine was adequately secured, thereby exposing workers to entanglement hazards.
Recent events (2)
- — I (O) $0
- — Z (O) $0
More inspections at Scan-Pac Manufacturing, INC.
View Scan-Pac Manufacturing, INC.'s full OSHA safety record →
More inspections in this industry (NAICS 333613)
More inspections in WI
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 344578968.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.