SAN ANTONIO, TX —
OSHA Inspection: PURE FLAVOR HOTHOUSE
Unprogrammed Other inspection · Safety discipline
At a glance
On , OSHA opened an unprogrammed Other safety inspection of PURE FLAVOR HOTHOUSE in 9610 BALL ST, SAN ANTONIO, TX 78218 (NAICS 311423). OSHA activity number 344669072.
OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- PURE FLAVOR HOTHOUSE
- Site address
- 9610 BALL ST
- City
- SAN ANTONIO
- State
- TX
- ZIP
- 78218
- Mailing
- 9610 BALL ST, SAN ANTONIO, TX 78218
What kind of inspection was it?
- Inspection type
- Unprogrammed Other (I)
- Scope
- Partial (B)
- Discipline
- Safety
- Advance notice
- No
- Union status
- B
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 311423
- Employees
- 97
- Ownership type
- A
Citations
4 citations on file for this inspection.
1910.176 A
- Issued
- Jul 1, 2020
- Abate by
- Jul 22, 2020
- Penalty
- Initial $8,675 · Current $5,205 Reduced
General-duty citation text
29 CFR 1910.176(a): Use of mechanical equipment. Where mechanical handling equipment is used, sufficient safe clearances shall be allowed for aisles, at loading docks, through doorways and wherever turns or passage must be made. Aisles and passageways shall be kept clear and in good repair, with no obstruction across or in aisles that could create a hazard. Permanent aisles and passageways shall be appropriately marked. Throughout the warehouse: On or about March, 03 2020, employees were exposed to struck-by hazards, while working near a Crown Electric Forklift without proper aisle and passageway markings.
Recent events (2)
- — I (S) $5205
- — Z (S) $8675
1910.219 C04 I
- Issued
- Jul 1, 2020
- Abate by
- Jul 22, 2020
- Penalty
- Initial $6,940 · Current $4,164 Reduced
General-duty citation text
29 CFR 1910.219(c)(4)(i): Projecting shaft ends shall present a smooth edge and end and shall not project more than one-half the diameter of the shaft unless guarded by nonrotating caps or safety sleeves. a. Production Staging Area, Top Sealer: On or about March, 03 2020, employees were exposed to caught in hazards, while working near unprotected rotating shaft. b. Production Staging Area, TX Wrap: On or about March, 03 2020, employees were exposed to caught in hazards, while working near unprotected rotating shaft. c. Production Staging Area, Over Wrap: On or about March, 03 2020, employees were exposed to caught in hazards, while working near unprotected rotating shaft. d. Production Staging Area, Line 3: On or about March, 03 2020, employees were exposed to caught in hazards, while working near unprotected rotating shaft.
Recent events (2)
- — I (S) $4164
- — Z (S) $6940
1910.303 B02
- Issued
- Jul 1, 2020
- Abate by
- Jul 22, 2020
- Penalty
- Initial $10,409 · Current $6,245 Reduced
General-duty citation text
29 CFR 1910.303(b)(2): Listed or labeled electrical equipment was not used or installed in accordance with instructions included in the listed or labeling: a. Production Staging Area, Top Sealer: On or about March, 03 2020, employees were exposed to electrical hazards, while connecting a scale and portable electrical tools into a quad-box outlet. b. Production Staging Area, TX Wrap: On or about March, 03 2020, employees were exposed to electrical hazards, while connecting a scale and portable electrical tools into a quad-box outlet. c. Production Staging Area, Over Wrap: On or about March, 03 2020, employees were exposed to electrical hazards, while connecting a scale and portable electrical tools into a quad-box outlet. d. Production Staging Area, Line 3: On or about March, 03 2020, employees were exposed to electrical hazards, while connecting a scale and portable electrical tools into a quad-box outlet.
Recent events (2)
- — I (S) $6245.4
- — Z (S) $10409
1910.305 G01 IV A
- Issued
- Jul 1, 2020
- Abate by
- Jul 22, 2020
- Penalty
- Initial $10,409 · Current $6,245 Reduced
General-duty citation text
29 CFR 1910.305(g)(1)(iv)(A): As a substitute for the fixed wiring of a structure: a. Production Staging Area, Top Sealer: On or about March, 03 2020, employees were exposed to electrical hazards, while connecting a scale and portable electrical tools into a quad-box outlet not being properly mounted. b. Production Staging Area, TX Wrap: On or about March, 03 2020, employees were exposed to electrical hazards, while connecting a scale and portable electrical tools into a quad-box outlet not being properly mounted. c. Production Staging Area, Over Wrap: On or about March, 03 2020, employees were exposed to electrical hazards, while connecting a scale and portable electrical tools into a quad-box outlet not being properly mounted. d. Production Staging Area, Line 3: On or about March, 03 2020, employees were exposed to electrical hazards, while connecting a scale and portable electrical tools into a quad-box outlet not being properly mounted.
Recent events (2)
- — I (S) $6245.4
- — Z (S) $10409
More inspections at Pure Flavor Hothouse
View Pure Flavor Hothouse's full OSHA safety record →
More inspections in this industry (NAICS 311423)
More inspections in TX
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 344669072.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.