SATANTA, KS —
OSHA Inspection: FRIONA CATTLE FEEDERS NORTH
Referral inspection · Safety discipline
At a glance
On , OSHA opened a referral safety inspection of FRIONA CATTLE FEEDERS NORTH in 1174 EMPIRE CIRCLE SUITE 601, SATANTA, KS 67870 (NAICS 112112). OSHA activity number 344891619.
OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- FRIONA CATTLE FEEDERS NORTH
- Site address
- 1174 EMPIRE CIRCLE SUITE 601
- City
- SATANTA
- State
- KS
- ZIP
- 67870
- Mailing
- 1174 EMPIRE CIRCLE SUITE 601, SATANTA, KS 67870
What kind of inspection was it?
- Inspection type
- Referral (C)
- Scope
- Partial (B)
- Discipline
- Safety
- Advance notice
- No
- Union status
- B
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 112112
- Employees
- 434
- Ownership type
- A
Citations
5 citations on file for this inspection.
1910.29 F04
- Issued
- Oct 13, 2020
- Abate by
- Nov 6, 2020
- Penalty
- Initial $9,639 · Current $0 Reduced
General-duty citation text
29 CFR 1910.29(f)(4): Openings in a stair rail system exceeded 19 inches at its least dimension: Employees monitoring grain levels in the south mill were exposed to fall hazards of up to approximately 8 feet from the walking surface to the ground below in that the stair rail system, installed prior to January 17, 2017, meeting the pre-January 17, 2017 top rail height requirements for a handrail/stair rail combination, was not equipped with a rail, was missing a rail on the left side and approximately 60 inch of the rail was missing on the right side
Recent events (3)
- — F (S) $0
- — C (S) $9639
- — Z (S) $9639
1910.219 C04
- Issued
- Oct 13, 2020
- Abate by
- Nov 6, 2020
- Penalty
- Initial $9,639 · Current $0 Reduced
General-duty citation text
29 CFR 1910.219(c)(4): Projecting shaft ends shall present a smooth edge and end and shall not project more than one-half the diameter of the shaft unless guarded by nonrotating caps or safety sleeves: In the South Mill Boiler Room, employees engaged in milling activities were exposed to a caught by hazard in that an exposed 4.5 inch diameter shaft end projected approximately 6.5 inches and was unguarded.
Recent events (3)
- — F (S) $0
- — C (S) $9639
- — Z (S) $9639
1910.252 A02 II
- Issued
- Oct 13, 2020
- Abate by
- Nov 6, 2020
- Penalty
- Initial $5,783 · Current $0 Reduced
General-duty citation text
29 CFR 1910.252(a)(2)(ii): Suitable extinguishing equipment was not maintained in a state of readiness for instant use: In the feedlot area, employees engaged in rail repairing activities were exposed fire hazards in that the fire extinguishers utilized in rail truck 281 were empty.
Recent events (3)
- — F (S) $0
- — C (S) $5783
- — Z (S) $5783
1910.253 A03
- Issued
- Oct 13, 2020
- Abate by
- Nov 6, 2020
- Penalty
- Initial $5,783 · Current $0 Reduced
General-duty citation text
29 CFR 1910.253(a)(3): Apparatus such as torches, regulators or pressure reducing valves, acetylene generators and manifolds used in an oxygen fuel gas system used in an oxygen fuel gas system had not been approved: In the feedlot area, employees engaged in rail repairing activities were exposed fire hazards in that employees were permitted to use an acetylene tank with an attached pressure gauge that was missing the gauge needle and protective cover.
Recent events (3)
- — F (S) $0
- — C (S) $5783
- — Z (S) $5783
1928.57 A11
- Issued
- Oct 13, 2020
- Abate by
- Mar 5, 2021
- Penalty
- Initial $13,494 · Current $9,446 Reduced
General-duty citation text
29 CFR 1928.57(a)(11): Where a moving machinery part presented a hazard during servicing or maintenance, the engine was not stopped, the power source was not disconnected, and all machine movement was not stopped before servicing or maintenance was performed: Employees engaged in maintenance activities were exposed to amputation and caught-in hazards in that the engine was not stopped on a feeder truck, the power source was not disconnected, and all machine movement was not stopped before maintenance was performed.
Recent events (3)
- — F (S) $9446
- — C (S) $13494
- — Z (S) $13494
More inspections at Friona Cattle Feeders North
View Friona Cattle Feeders North's full OSHA safety record →
More inspections in this industry (NAICS 112112)
More inspections in KS
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 344891619.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.