HOUSTON, TX —
OSHA Inspection: AMTEX MACHINE PRODUCTS, INC
Complaint inspection · Safety discipline
At a glance
On , OSHA opened a complaint safety inspection of AMTEX MACHINE PRODUCTS, INC in 4517 BRITTMOORE ROAD, HOUSTON, TX 77041 (NAICS 332996). OSHA activity number 345086987.
What this inspection record means
OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Watch Amtex Machine Products, INC — free
Get an email when a new federal OSHA severe-injury report for Amtex Machine Products, INC is published. One employer, no account, unsubscribe in one click.
Where did this inspection happen?
- Establishment
- AMTEX MACHINE PRODUCTS, INC
- Site address
- 4517 BRITTMOORE ROAD
- City
- HOUSTON
- State
- TX
- ZIP
- 77041
- Mailing
- 4517 BRITTMOORE ROAD, HOUSTON, TX 77041
What kind of inspection was it?
- Inspection type
- Complaint (B)
- Scope
- Partial (B)
- Discipline
- Safety
- Advance notice
- No
- Union status
- B
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 332996
- Employees
- 66
- Ownership type
- A
Citations
4 citations on file for this inspection.
1910.147 C04 I
- Issued
- Mar 31, 2021
- Abate by
- Apr 19, 2021
- Penalty
- Initial $9,557 · Current $9,557
General-duty citation text
29 CFR 1910.147(c)(4)(i):Procedures were not developed, documented and utilized for the control of potentially hazardous energy when employees were engaged in activities covered by this section. On or about January 05, 2021, and at times prior thereto: a. In the A Shop, employees were exposed to electrical, struck-by and caught-by hazards, when performing service or maintenance on CNC A-01, DAEWOO PUMA 10HC / serial# PH100518 without utilizing an effective energy control procedure. b. In the A Shop, employees were exposed to electrical, struck-by and caught-by hazards, when performing service or maintenance on CNC A-02, DAEWOO PUMA 240 C / serial# PM242146 without utilizing an effective energy control procedure. c. In the A Shop, employees were exposed to electrical, struck-by and caught-by hazards, when performing service or maintenance on CNC A-05, DAEWOO PUMA 15 / serial# PM150231 without utilizing an effective energy control procedure. d. In the A Shop, employees were exposed to electrical, struck-by and caught-by hazards, when performing service or maintenance on CNC A-06, KIA SKT-460 / serial# G3130-0286 without utilizing an effective energy control procedure. e. In the A Shop, employees were exposed to electrical, struck-by and caught-by hazards, when performing service or maintenance on CNC A-09, KIA SKT-300 / serial# G3158-0432 without utilizing an effective energy control procedure. f. In the A Shop, employees were exposed to electrical, struck-by and caught-by hazards, when performing service or maintenance on CNC A-15, KIA SKT-300 / serial# G3158-0437 without utilizing an effective energy control procedure. g. In the A Shop, employees were exposed to electrical, struck-by and caught-by hazards, when performing service or maintenance on CNC A-16, KIA L 300 LC / serial# G3732-0148 without utilizing an effective energy control procedure. h. In the A Shop, employees were exposed to electrical, struck-by and caught-by hazards, when performing service or maintenance on CNC A-18, DAEWOO PUMA 400 B / serial# PM351547 without utilizing an effective energy control procedure. i. In the A Shop, employees were exposed to electrical, struck-by and caught-by hazards, when performing service or maintenance on CNC A-20, MIGHTY VIPER VT-30GL / serial# 8331207011 without utilizing an effective energy control procedure. j. In the A Shop, employees were exposed to electrical, struck-by and caught-by hazards, when performing service or maintenance on CNC A-21, KIA SKT-300 / serial# G3158-0444 without utilizing an effective energy control procedure. k. In the A Shop, employees were exposed to electrical, struck-by and caught-by hazards, when performing service or maintenance on CNC A-23, DAEWOO PUMA 300 C / serial# PM303074 without utilizing an effective energy control procedure. l. In the A Shop, employees were exposed to electrical, struck-by and caught-by hazards, when performing service or maintenance on CNC A-25, KIA SKT-300 / serial# G3158-0436 without utilizing an effective energy control procedure. m. In the B Shop, employees were exposed to electrical, struck-by and caught-by hazards, when performing service or maintenance on CNC B-02, DOOSAN PUMA 480 / serial# ML0144-000470 without utilizing an effective energy control procedure. n. In the B Shop, employees were exposed to electrical, struck-by and caught-by hazards, when performing service or maintenance on CNC B-04, DOOSAN PUMA 480 / serial# ML0144-000350 without utilizing an effective energy control procedure. o. In the B Shop, employees were exposed to electrical, struck-by and caught-by hazards, when performing service or maintenance on CNC B-05, DAEWOO PUMA 480 / serial# ML0144-000360 without utilizing an effective energy control procedure. p. In the B Shop, employees were exposed to electrical, struck-by and caught-by hazards, when performing service or maintenance on CNC B-10, KIA L 400 C / serial# G3729-0125 without utilizing an effective energy control procedure. q. In the B Shop, employees were exposed to electrical, struck-by and caught-by hazards, when performing service or maintenance on CNC B-15, WIA L400C / serial# G3729-0177 without utilizing an effective energy control procedure. r. In the B Shop, employees were exposed to electrical, struck-by and caught-by hazards, when performing service or maintenance on CNC B-16, WIA L400C / serial# G3729-0178 without utilizing an effective energy control procedure. s. In the B Shop, employees were exposed to electrical, struck-by and caught-by hazards, when performing service or maintenance on CNC B-19, KIA L300C / serial# G3158-0581 without utilizing an effective energy control procedure. t. In the B Shop, employees were exposed to electrical, struck-by and caught-by hazards, when performing service or maintenance on CNC B-27, WIA L300C / serial# G3158-0567 without utilizing an effective energy control procedure. u. In the B Shop, employees were exposed to electrical, struck-by and caught-by hazards, when performing service or maintenance on CNC B-28, KIA L300C / serial# G3158- 0481 without utilizing an effective energy control procedure. v. In the B Shop, employees were exposed to electrical, struck-by and caught-by hazards, when performing service or maintenance on CNC B-29, KIA L300A / serial# G3154-0564 without utilizing an effective energy control procedure.
Recent events (3)
- — F (S) $9557
- — C (S) $9557
- — Z (S) $9557
1910.303 B06
- Issued
- Mar 31, 2021
- Abate by
- Apr 19, 2021
- Penalty
- Initial $9,557 · Current $0 Reduced
General-duty citation text
29 CFR 1910.303(b)(6):Conductors or equipment were located in damp or wet locations; where exposed to gases, fumes, vapors, liquids, or other agents that had a deteriorating effect on the conductors or equipment; or where exposed to excessive temperatures and were not identified for use in the operating environment. On or about January 05, 2021, and at times prior thereto, in the plating line area, employees were exposed to electrical hazards while using a hose to spray water to lifting baskets within inches of electrical panels, outlets and switches.
Recent events (3)
- — F (S) $0
- — C (S) $9557
- — Z (S) $9557
1910.212 A01
- Issued
- Mar 31, 2021
- Abate by
- Apr 19, 2021
- Penalty
- Initial $9,557 · Current $0 Reduced
General-duty citation text
29 CFR 1910.212(a)(1):One or more methods of machine guarding was not provided to protect the operator and other employees in the machine area from hazards such as those created by point of operation, ingoing nip points, rotating parts, flying chips and sparks. On or about January 05, 2021, and at times prior thereto: a. In the A Shop, employees were exposed to struck-by and caught-by hazards, when operating CNC A-01, DAEWOO PUMA 10HC / serial# PH100518 without a functioning door interlock. b. In the A Shop, employees were exposed to struck-by and caught-by hazards, when operating CNC A-02, DAEWOO PUMA 240 C / serial# PM242146 without a functioning door interlock. c. In the A Shop, employees were exposed to struck-by and caught-by hazards, when operating CNC A-05, DAEWOO PUMA 15 / serial# PM150231 without a functioning door interlock. d. In the A Shop, employees were exposed to struck-by and caught-by hazards, when operating CNC A-06, KIA SKT-460 / serial# G3130-0286 without a functioning door interlock. e. In the A Shop, employees were exposed to struck-by and caught-by hazards, when operating CNC A-09, KIA SKT-300 / serial# G3158-0432 without a functioning door interlock. f. In the A Shop, employees were exposed to struck-by and caught-by hazards, when operating CNC A-15, KIA SKT-300 / serial# G3158-0437 without a functioning door interlock. g. In the A Shop, employees were exposed to struck-by and caught-by hazards, when operating CNC A-16, KIA L 300 LC / serial# G3732-0148 without a functioning door interlock. h. In the A Shop, employees were exposed to struck-by and caught-by hazards, when operating CNC A-18, DAEWOO PUMA 400 B / serial# PM351547 without a functioning door interlock. i. In the A Shop, employees were exposed to struck-by and caught-by hazards, when operating CNC A-20, MIGHTY VIPER VT-30GL / serial# 8331207011 without a functioning door interlock. j. In the A Shop, employees were exposed to struck-by and caught-by hazards, when operating CNC A-21, KIA SKT-300 / serial# G3158-0444 without a functioning door interlock. k. In the A Shop, employees were exposed to struck-by and caught-by hazards, when operating CNC A-23, DAEWOO PUMA 300 C / serial# PM303074 without a functioning door interlock. l. In the A Shop, employees were exposed to struck-by and caught-by hazards, when operating CNC A-25, KIA SKT-300 / serial# G3158-0436 without a functioning door interlock. m. In the B Shop, employees were exposed to struck-by and caught-by hazards, when operating CNC B-02, DOOSAN PUMA 480 / serial# ML0144-000470 without a functioning door interlock. n. In the B Shop, employees were exposed to struck-by and caught-by hazards, when operating CNC B-04, DOOSAN PUMA 480 / serial# ML0144-000350 without a functioning door interlock. o. In the B Shop, employees were exposed to struck-by and caught-by hazards, when operating CNC B-05, DAEWOO PUMA 480 / serial# ML0144-000360 without a functioning door interlock. p. In the B Shop, employees were exposed to struck-by and caught-by hazards, when operating CNC B-10, KIA L 400 C / serial# G3729-0125 without a functioning door interlock. q. In the B Shop, employees were exposed to struck-by and caught-by hazards, when operating CNC B-15, WIA L400C / serial# G3729-0177 without a functioning door interlock. r. In the B Shop, employees were exposed to struck-by and caught-by hazards, when operating CNC B-16, WIA L400C / serial# G3729-0178 without a functioning door interlock. s. In the B Shop, employees were exposed to struck-by and caught-by hazards, when operating CNC B-19, KIA L300C / serial# G3158-0581 without a functioning door interlock. t. In the B Shop, employees were exposed to struck-by and caught-by hazards, when operating CNC B-27, WIA L300C / serial# G3158-0567 without a functioning door interlock. u. In the B Shop, employees were exposed to struck-by and caught-by hazards, when operating CNC B-28, KIA L300C / serial# G3158- 0481 without a functioning door interlock. v. In the B Shop, employees were exposed to struck-by and caught-by hazards, when operating CNC B-29, KIA L300A / serial# G3154-0564 without a functioning door interlock.
Recent events (3)
- — F (S) $0
- — C (S) $9557
- — Z (S) $9557
1910.219 F03
- Issued
- Mar 31, 2021
- Abate by
- Apr 19, 2021
- Penalty
- Initial $6,827 · Current $6,827
General-duty citation text
29 CFR 1910.219(f)(3):Sprocket wheels and chains which were seven (7) feet or less above floors or platforms were not enclosed. On or about January 05, 2021, and at times prior thereto, in the B Shop, employees were exposed to caught-by hazards when working and walking near the chain and sprocket of the conveyer of the B5 CNC without a guard enclosing the chain and sprocket.
Recent events (3)
- — F (S) $6827
- — C (S) $6827
- — Z (S) $6827
More inspections at Amtex Machine Products, INC
View Amtex Machine Products, INC's full OSHA safety record →
More inspections in this industry (NAICS 332996)
Jul 7, 2026
Next Mechanical · ELK POINT, SD
Jun 25, 2026
Enerfab Modular Shop · HARRISON, OH
Jun 15, 2026
Pioneer Pipe Contractors, INC. · PENNSAUKEN, NJ
May 28, 2026
Island Industries, INC. · MEMPHIS, TN
May 27, 2026
Ferguson Enterprises, LLC · LEBANON, TN
More inspections in TX
Jul 17, 2026
Cornelius Nurseries, INC. · RICHMOND, TX
Jul 17, 2026
Holloway Houston, INC. · HOUSTON, TX
Jul 17, 2026
Voluntary Purchasing Groups, INC. · BONHAM, TX
Jul 16, 2026
Rnwbl · SNYDER, TX
Jul 16, 2026
United Rentals, INC. · WICHITA FALLS, TX
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 345086987.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.