LUBBOCK, TX —
OSHA Inspection: JM FRAMING & REMODELING INC
Planned inspection · Safety discipline
At a glance
On , OSHA opened a planned safety inspection of JM FRAMING & REMODELING INC in 5317 110TH STREET, ABBEY GLEN LOT #54-A, LUBBOCK, TX 79424 (NAICS 238130). OSHA activity number 345139893.
OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- JM FRAMING & REMODELING INC
- Site address
- 5317 110TH STREET, ABBEY GLEN LOT #54-A
- City
- LUBBOCK
- State
- TX
- ZIP
- 79424
- Mailing
- 2811 DARTMOUTH ST, LUBBOCK, TX 79415
What kind of inspection was it?
- Inspection type
- Planned (H)
- Scope
- Partial (B)
- Discipline
- Safety
- Advance notice
- No
- Union status
- B
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 238130
- Employees
- 4
- Ownership type
- A
Citations
4 citations on file for this inspection.
1926.102 A01
- Issued
- Jul 22, 2021
- Abate by
- Aug 19, 2021
- Penalty
- Initial $1,755 · Current $1,755
General-duty citation text
29 CFR 1926.102(a)(1): The employer shall ensure that each affected employee uses appropriate eye or face protection when exposed to eye or face hazards from flying particles, and debris. Employees engaged in framing activities were exposed to struck-by-hazards when using pneumatic nail gun without the use of eye protection.
Recent events (1)
- — Z (S) $1755
1926.501 B13
- Issued
- Jul 22, 2021
- Abate by
- Aug 19, 2021
- Penalty
- Initial $3,511 · Current $3,511
General-duty citation text
29 CFR 1926.501(b)(13): Each employee engaged in residential construction activities 6 feet (1.8 m) or more above lower levels shall be protected by guardrail systems, safety net system, or personal fall arrest system unless another provision in paragraph (b) of this section provides for an alternative fall protection measure. Exception: When the employer can demonstrate that it is infeasible or creates a greater hazard to use these systems, the employer shall develop and implement a fall protection plan which meets the requirements of paragraph1926.501(b): Employees engaged in framing activities were exposed to fall hazards in excess of six (6) feet. JM Framing & Remodeling was previously cited for a violation of the occupational safety and health standard or its equivalent standard 1926.501(b)(13), which was contained in OSHA inspection number 1420258, citation number 1, item number 2/a, and was affirmed as a final order on 09/05/2019 with respect to a workplace located at 9612 Hyden Ave., Lubbock, Texas.
Recent events (1)
- — Z (R) $3511
1926.503 A01
- Issued
- Jul 22, 2021
- Abate by
- Aug 19, 2021
- Penalty
- Initial $234 · Current $234
General-duty citation text
29 CFR 1926.503(a)(1): The employer shall provide a training program for each employee who might be exposed to fall hazards. The program shall enable each employee to recognize the hazards of falling and shall train each employee in the procedures to be followed in order to minimize these hazards: Employees engaged in framing activities were not provided fall protection training to enable the employees to understand the importance of wearing fall protection above six (6) feet. JM Framing & Remodeling was previously cited for a violation of this occupational safety and health standard or its equivalent standard 1926.5013(a)(1), which was contained in OSHA inspection number 1420258, citation number 1, item number 2/b and was affirmed as a final order on 09/05/2019 with respect to a workplace located at 9612 Hayden Ave., Lubbock, Texas
Recent events (1)
- — Z (R) $234
1926.1060 A
- Issued
- Jul 22, 2021
- Abate by
- Aug 19, 2021
- Penalty
- Initial $234 · Current $234
General-duty citation text
29 CFR 1926.1060(a): The employer shall provide a training program for each employee using ladders and stairways, as necessary. The program shall enable each employee to recognize hazards related to ladders and stairways, and shall train each employee in the procedures to be followed to minimize these hazards: Employees performing framing activities by climbing on a ladder to access the upper level, had not been trained to recognize the hazards related to ladders and the procedures to follow that would minimize the hazards. JM Framing & Remodeling was previously cited for a violation of this occupational safety and health standard or its equivalent standard 1926.1060(a), which was contained in OSHA inspection number 1420258, citation number 1, item number 3/a and was affirmed as a final order on 09/05/2019 with respect to a workplace located at 9612 Hayden Ave., Lubbock, Texas
Recent events (1)
- — Z (R) $234
More inspections at JM Framing & Remodeling INC
View JM Framing & Remodeling INC's full OSHA safety record →
More inspections in this industry (NAICS 238130)
More inspections in TX
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 345139893.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.