FORT BRAGG, NC —
OSHA Inspection: DEPARTMENT OF DEFENSE EDUCATION ACTIVITY
Referral inspection · Safety discipline
At a glance
On , OSHA opened a referral safety inspection of DEPARTMENT OF DEFENSE EDUCATION ACTIVITY in 4931 HONEYCUTT RD, BLDG 6036, FORT BRAGG, NC 28307 (NAICS 928110). OSHA activity number 345187025.
OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- DEPARTMENT OF DEFENSE EDUCATION ACTIVITY
- Site address
- 4931 HONEYCUTT RD, BLDG 6036
- City
- FORT BRAGG
- State
- NC
- ZIP
- 28307
- Mailing
- 4931 HONEYCUTT RD, BLDG 6036, FORT BRAGG, NC 28307
What kind of inspection was it?
- Inspection type
- Referral (C)
- Scope
- Complete (A)
- Discipline
- Safety
- Advance notice
- No
- Union status
- B
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 928110
- Employees
- 350
- Ownership type
- D
Citations
7 citations on file for this inspection.
1910.101 B
- Issued
- Mar 15, 2021
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.101(b): Before using cylinder, be sure it is properly supported to prevent it from being knocked over. On or before February 3, 2021, nitrogen cylinders were not secured to prevent them from being knocked over.
Recent events (1)
- — Z (S) $0
1910.213 D01
- Issued
- Mar 15, 2021
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.213(d)(1): Each circular crosscut table saw shall be guarded by a hood which shall meet all the requirements of paragraph (c)(1) of this section for hoods for circular ripsaws. On or before February 3, 2021, Ridgid table saw was not properly guarded.
Recent events (1)
- — Z (S) $0
1910.215 A04
- Issued
- Mar 15, 2021
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.215(a)(4):Grinding machinery was not used with work rest(s) to support offhand grinding work: On or before February 3, 2021, the work rest installed on the left side of a Westward 6 inch grinder was not adjusted to a maximum opening of one-eight inch.
Recent events (1)
- — Z (S) $0
1910.303 B02
- Issued
- Mar 15, 2021
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.303(b)(2):Installation and use. Listed or labeled equipment shall be installed and used in accordance with any instructions included in the listing or labeling. On or before February 3, 2021, A re-locatable power tap, designed and listed for being used with high concentrations of low powered loads was instead used with high-powered loads such as a refrigerator.
Recent events (1)
- — Z (S) $0
1910.303 B08 I
- Issued
- Mar 15, 2021
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.303(b)(8)(i):Electric equipment shall be firmly secured to the surface on which it is mounted. On or before February 3, 2021, employer did not ensure a Rigid pipe-threading machine was properly secured.
Recent events (1)
- — Z (S) $0
1910.304 G05
- Issued
- Mar 15, 2021
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.304(g)(5):Grounding path. The path to ground from circuits, equipment, and enclosures shall be permanent, continuous, and effective. On or about February 3, 2021, flexible cord used to power a floor cleaner was missing its ground pin.
Recent events (1)
- — Z (S) $0
1910.305 G02 III
- Issued
- Mar 15, 2021
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.305(g)(2)(iii):Flexible cords and cables shall be connected to devices and fittings so that strain relief is provided that will prevent pull from being directly transmitted to joints or terminal screws. On or before February 3, 2021, Ice Machine flexible cord was not connected so that strain relief was provided that would prevent pull from being directly transmitted to joints or terminal screws.
Recent events (1)
- — Z (S) $0
More inspections at Department of Defense Education Activity
View Department of Defense Education Activity's full OSHA safety record →
More inspections in this industry (NAICS 928110)
More inspections in NC
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 345187025.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.