ELK GROVE VILLAGE, IL —
OSHA Inspection: AMERICAN MOLDING TECHNOLOGIES, INC.
Complaint inspection · Safety discipline
At a glance
On , OSHA opened a complaint safety inspection of AMERICAN MOLDING TECHNOLOGIES, INC. in 2350 E. LUNT, ELK GROVE VILLAGE, IL 60007 (NAICS 326199). OSHA activity number 345389753.
OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- AMERICAN MOLDING TECHNOLOGIES, INC.
- Site address
- 2350 E. LUNT
- City
- ELK GROVE VILLAGE
- State
- IL
- ZIP
- 60007
- Mailing
- 2350 E. LUNT, ELK GROVE VILLAGE, IL 60007
What kind of inspection was it?
- Inspection type
- Complaint (B)
- Scope
- Partial (B)
- Discipline
- Safety
- Advance notice
- No
- Union status
- B
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 326199
- Employees
- 60
- Ownership type
- A
Citations
2 citations on file for this inspection.
1910.147 C01
- Issued
- Aug 12, 2021
- Abate by
- Sep 8, 2021
- Penalty
- Initial $6,827 · Current $6,827
General-duty citation text
29 CFR 1910.147(c)(1): The employer did not establish a program consisting of an energy control procedure, employee training, and periodic inspections to ensure that before any employee performed any servicing or maintenance on a machine or equipment where the unexpected energizing, startup, or release of stored energy could occur and cause injury, the machine or equipment shall be isolated from the energy source and rendered inoperative: a) Injection Molding Department- On or about June 21, 2021, the employer did not develop, document, or utilize an energy control program (lockout/tagout program), that included an energy control procedure for employees who perform set-up to follow, training to ensure that all required elements of the procedure were understood by employees, including safe application, usage, and removal of the energy isolating controls, and periodic inspections to ensure that employees were protected from injuries caused by the unexpected energizing of equipment or release of stored energy while performing setup of the Injection Molding Presses and cleaning molds. In accordance with 29 CFR 1903.19(c), abatement certification is required for this violation (using CERTIFICATION OF CORRECTIVE ACTION WORKSHEET), and in addition, documentation that abatement is complete must be included with your certification. This documentation may include, but is not limited to, evidence of the purchase or repair of the equipment, photographic or video evidence of abatement or other written records.
Recent events (1)
- — Z (S) $6827
1910.147 C01
- Issued
- Aug 12, 2021
- Abate by
- Sep 8, 2021
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.147(c)(1): The employer did not establish a program consisting of an energy control procedure, employee training, and periodic inspections to ensure that before any employee performed any servicing or maintenance on a machine or equipment where the unexpected energizing, startup, or release of stored energy could occur and cause injury, the machine or equipment shall be isolated from the energy source and rendered inoperative: a) Extrusion and Injection Molding Departments - On or about June 21, 2021, the employer did not develop, document, or utilize an energy control program (lockout/tagout program), that included an energy control procedure for maintenance employees to follow, training to ensure that all required elements of the procedure were understood by employees, including safe application, usage, and removal of the energy isolating controls, and periodic inspections to ensure that employees were protected from injuries caused by the unexpected energizing of equipment or release of stored energy while performing servicing or maintenance on equipment, such as performing repairs and changing blades on equipment. In accordance with 29 CFR 1903.19(c), abatement certification is required for this violation (using the CERTIFICATION OF CORRECTIVE ACTION WORKSHEET).
Recent events (1)
- — Z (O) $0
More inspections at American Molding Technologies, INC.
View American Molding Technologies, INC.'s full OSHA safety record →
More inspections in this industry (NAICS 326199)
More inspections in IL
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 345389753.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.