TOMAH, WI —
OSHA Inspection: GENERAL SHEET METAL WORKS INCORPORATED
Federal Agency inspection · Safety discipline
At a glance
On , OSHA opened a federal Agency safety inspection of GENERAL SHEET METAL WORKS INCORPORATED in 328 CARDINAL AVENUE, TOMAH, WI 54660 (NAICS 323111). OSHA activity number 345535967.
OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- GENERAL SHEET METAL WORKS INCORPORATED
- Site address
- 328 CARDINAL AVENUE
- City
- TOMAH
- State
- WI
- ZIP
- 54660
- Mailing
- 328 CARDINAL AVENUE, TOMAH, WI 54660
What kind of inspection was it?
- Inspection type
- Federal Agency (M)
- Scope
- Partial (B)
- Discipline
- Safety
- Advance notice
- No
- Union status
- B
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 323111
- Employees
- 78
- Ownership type
- A
Citations
4 citations on file for this inspection.
1910.147 C04 I
- Issued
- Mar 10, 2022
- Abate by
- Apr 15, 2022
- Penalty
- Initial $14,502 · Current $11,000 Reduced
General-duty citation text
29 CFR 1910.147(c)(4)(i):Procedures were not developed, documented and utilized for the control of potentially hazardous energy when employees were engaged in activities covered by this section: Procedures were not developed for Trumpf laser operators and maintenance employees when entering the material handling area to perform servicing and maintenance tasks: a. On or about September 17, 2021, a maintenance employee entered the material handling area to adjust slat bolts on index table. b. On or about September 17, 2021, and October 19, 2021, laser operators entered the material handling area to clean the index table slats. c. On or about October 01, 2021, to October 08, 2021, laser operators entered the material handling area to replace index table slats. d. On or about September 17, 2021, laser operators entered the material handling area to perform cleaning activities.
Recent events (2)
- — I (S) $11000
- — Z (S) $14502
1910.147 C07 I A
- Issued
- Mar 10, 2022
- Abate by
- Apr 15, 2022
- Penalty
- Initial $14,502 · Current $11,000 Reduced
General-duty citation text
29 CFR 1910.147(c)(7)(i)(A):Authorized employee(s) did not receive training in the recognition of applicable hazardous energy sources, the type and magnitude of the energy available in the workplace, and the methods and means necessary for energy isolation: On or about September 30, 2021 laser operators did not received authorized training when laser operators: a. On or about September 17, 2021, and October 19, 2021, laser operators entered the material handling area to clean the index table slats. b. On or about October 01, 2021, to October 08, 2021, laser operators entered the material handling area to replace index table slats. c. On or about September 17, 2021, laser operators entered the material handling area to perform cleaning activities.
Recent events (2)
- — I (S) $11000
- — Z (S) $14502
1910.147 D03
- Issued
- Mar 10, 2022
- Abate by
- Apr 15, 2022
- Penalty
- Initial $14,502 · Current $11,000 Reduced
General-duty citation text
29 CFR 1910.147(d)(3): All energy isolating devices that were needed to control the energy to the machine or equipment were not physically located and operated in such a manner as to isolate the machine or equipment from the energy source(s): Energy isolating devices were not used to de-energize Trumpf laser material handling area: a. On or about September 17, 2021, a maintenance employee entered the material handling area to adjust slat bolts on index table. b. On or about September 17, 2021, and October 19, 2021, laser operators entered the material handling area to clean the index table slats. c. On or about October 01, 2021, to October 08, 2021, laser operators entered the material handling area to replace index table slats. d. On or about September 17, 2021, laser operators entered the material handling area to perform cleaning activities.
Recent events (2)
- — I (S) $11000
- — Z (S) $14502
1910.147 D04 I
- Issued
- Mar 10, 2022
- Abate by
- Apr 7, 2022
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.147(d)(4)(i):Lockout or tagout devices were not affixed to each energy isolating device by authorized employees: Maintenance and laser operator did not affix energy control devices to Trumpf laser material handling lifts: a. On or about September 17, 2021, a maintenance employee entered the material handling area to adjust slat bolts on index table. b. On or about September 17, 2021, and October 19, 2021, laser operators entered the material handling area to clean the index table slats. c. On or about October 01, 2021, to October 08, 2021, laser operators entered the material handling area to replace index table slats. d. On or about September 17, 2021, laser operators entered the material handling area to perform cleaning activities.
Recent events (2)
- — I (S) $0
- — Z (S) $0
More inspections at General Sheet Metal Works Incorporated
View General Sheet Metal Works Incorporated's full OSHA safety record →
More inspections in this industry (NAICS 323111)
More inspections in WI
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 345535967.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.