FRANKLIN, OH —
OSHA Inspection: H & W SCREW PRODUCTS, INC.
Referral inspection · Safety discipline
At a glance
On , OSHA opened a referral safety inspection of H & W SCREW PRODUCTS, INC. in 335 INDUSTRIAL DRIVE, FRANKLIN, OH 45005 (NAICS 332722). OSHA activity number 345604367.
OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- H & W SCREW PRODUCTS, INC.
- Site address
- 335 INDUSTRIAL DRIVE
- City
- FRANKLIN
- State
- OH
- ZIP
- 45005
- Mailing
- 335 INDUSTRIAL DRIVE, FRANKLIN, OH 45005
What kind of inspection was it?
- Inspection type
- Referral (C)
- Scope
- Partial (B)
- Discipline
- Safety
- Advance notice
- No
- Union status
- B
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 332722
- Employees
- 15
- Ownership type
- A
Citations
2 citations on file for this inspection.
1910.147 C01
- Issued
- Feb 22, 2022
- Abate by
- Mar 18, 2022
- Penalty
- Initial $5,801 · Current $5,801
General-duty citation text
29 CFR 1910.147(c)(1): Energy control program. The employer shall establish a program consisting of energy control procedures, employee training and periodic inspections to ensure that before any employee performs any servicing or maintenance on a machine or equipment where the unexpected energizing, startup or release of stored energy could occur and cause injury, the machine or equipment shall be isolated from the energy source and rendered inoperative. a) On or about October 20, 2022, the employer did not have an energy control program that included specific energy isolation procedures, training for authorized, affected, and other employees, and periodic inspections of the procedures on an annual basis for equipment such as but not limited to; the CNC Lathes.
Recent events (1)
- — Z (S) $5801
1910.147 D
- Issued
- Feb 22, 2022
- Abate by
- Mar 18, 2022
- Penalty
- Initial $5,801 · Current $5,801
General-duty citation text
29 CFR 1910.147(d): Application of control. The established procedures for the application of energy control (the lockout or tagout procedures) shall cover the following elements and actions and shall be done in the following sequence: a) On or about October 20, 2022, on the Miyano LE 22 B CNC Lathe, each Lathe machine operator performing servicing operations did not lock out the electrical disconnects when performing tasks such as removing the chuck. Each employee was not required to: (1) turn off and shut down the machines, (2) physically locate and operate energy isolating devices in such a manner as to isolate the machine or equipment from the electric and pneumatic energy sources, (3) affix lockout or tagout devices to each energy-isolating device, (4) verify the effectiveness of energy isolation.
Recent events (1)
- — Z (S) $5801
More inspections at H & W Screw Products, INC.
View H & W Screw Products, INC.'s full OSHA safety record →
More inspections in this industry (NAICS 332722)
More inspections in OH
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 345604367.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.