GENEVA, IL —
OSHA Inspection: BAR TECHNOLOGIES, L.L.C.
Federal Agency inspection · Safety discipline
At a glance
On , OSHA opened a federal Agency safety inspection of BAR TECHNOLOGIES, L.L.C. in 500 FLUID POWER DRIVE, GENEVA, IL 60134 (NAICS 331221). OSHA activity number 345679781.
OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- BAR TECHNOLOGIES, L.L.C.
- Site address
- 500 FLUID POWER DRIVE
- City
- GENEVA
- State
- IL
- ZIP
- 60134
- Mailing
- 500 FLUID POWER DRIVE, GENEVA, IL 60134
What kind of inspection was it?
- Inspection type
- Federal Agency (M)
- Scope
- Partial (B)
- Discipline
- Safety
- Advance notice
- No
- Union status
- B
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 331221
- Employees
- 26
- Ownership type
- A
Citations
2 citations on file for this inspection.
1910.147 C07 I
- Issued
- May 12, 2022
- Abate by
- Jun 10, 2022
- Penalty
- Initial $14,502 · Current $14,502
General-duty citation text
29 CFR 1910.147(c)(7)(i):The employer did not provide training to ensure that the purpose and function of the energy control program are understood by employees and that the knowledge and skills required for the safe application, usage, and removal of the energy controls are acquired by employees: On or about December 9, 2021, the employer did not ensure that employees were trained to isolate hazardous energy sources prior to engaging in servicing and maintenance activities. Employees performed setup and tool changes on the Hetran turning machine without first shutting down and locking out the hydraulic and electrical energy sources, exposing them to crushing injuries. Abatement documentation is required for this item in accordance with the requirements of 29 CFR 1903.19(d).
Recent events (2)
- — I (S) $14502
- — Z (S) $14502
1910.147 D
- Issued
- May 12, 2022
- Abate by
- Jul 15, 2022
- Penalty
- Initial $14,502 · Current $14,502
General-duty citation text
29 CFR 1910.147(d): The application of energy control (lockout or tagout) actions were not done in the following sequence: On or about December 9, 2021 employee(s) performed servicing and maintenance tasks such as setup on the Hetran Machine, and were exposed to bodily injury and crushing hazards due to unexpected startup and/or energy release of stored energy. Employees were not required to control hazardous energy sources in the following sequence: (1) prepare for shutdown, (2) shut down machine or equipment, (3) physically locate and operate energy isolating devices in such a manner as to isolate the machine or equipment from the energy source, (4) affix lockout or tagout devices to each energy isolating device by authorized employee, (5) relieve, disconnect, restrain or otherwise render safe all stored or residual energy, (6) verify that isolation and deenergization of the machine or equipment have been accomplished: Abatement documentation is required for this item in accordance with the requirements of 29 CFR 1903.19(d).
Recent events (2)
- — I (S) $14502
- — Z (S) $14502
More inspections at BAR Technologies, L.L.C.
View BAR Technologies, L.L.C.'s full OSHA safety record →
More inspections in this industry (NAICS 331221)
More inspections in IL
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 345679781.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.