FORT WORTH, TX ·
OSHA Inspection: OMAR ZURITA TENORIO
Planned inspection · Health discipline
At a glance
On , OSHA opened a planned health inspection of OMAR ZURITA TENORIO in 2513 PEORIA, FORT WORTH, TX 76179 (NAICS 238140). OSHA activity number 345775993.
OSHA opens inspections for many reasons: routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- OMAR ZURITA TENORIO
- Site address
- 2513 PEORIA
- City
- FORT WORTH
- State
- TX
- ZIP
- 76179
- Mailing
- 5301 SPRINGLAKE PKWY APT# 2019, HALTOM CITY, TX 76117
What kind of inspection was it?
- Inspection type
- Planned (H)
- Scope
- Partial (B)
- Discipline
- Health
- Advance notice
- No
- Union status
- Non-union (B)
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 238140
- Employees
- 2
- Ownership type
- Private (A)
Citations
4 citations on file for this inspection.
1926.102 A01
- Issued
- Feb 24, 2022
- Penalty
- Initial $1,585 · Current $1,585
General-duty citation text
29 CFR 1926.102(a)(1):Employees did not use eye and face protection equipment when machines or operations presented potential eye or face injury from physical, chemical, or radiation agents. On the construction site, an employee engaged in cutting masonry material with a DeWalt brick masonry saw was not wearing eye protection and exposed to struck-by hazards from flying particles.
Recent events (1)
- · Z (S) $1585
1926.300 B01
- Issued
- Feb 24, 2022
- Penalty
- Initial $1,585 · Current $1,585
General-duty citation text
29 CFR 1926.300(b)(1): Power operated tool(s), designed to accommodate guards, were not equipped with such guards when in use. On the construction site, an employee operating a DeWalt cut off saw with the lower guard missing was exposed to cuts and laceration hazards.
Recent events (1)
- · Z (S) $1585
1926.1153 C01
- Issued
- Feb 24, 2022
- Penalty
- Initial $2,113 · Current $2,113
General-duty citation text
29 CFR 1926.1153(c)(1): For each employee engaged in a task identified on Table 1, the employer did not fully and properly implement the engineering controls, work practices, and respiratory protection specified for the task on Table 1, unless the employer assesses and limits the exposure of the employee to respirable crystalline silica in accordance with paragraph (d) of this section. On the construction site, the employer did not ensure the employee using a DeWalt cut off saw to cut masonry material was protected from being expose to silica with the use of engineering controls, work practices and respiratory protection.
Recent events (1)
- · Z (S) $2113
1926.1153 D02 I
- Issued
- Feb 24, 2022
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1926.1153(d)(2)(i): The employer did not assess the exposure of each employee who was or may reasonably be expected to be exposed to respirable crystalline silica at or above the action level in accordance with either the performance option in paragraph (d)(2)(ii) or the scheduled monitoring option in paragraph (d)(2)(iii) of this section: On the construction site, the employer did not access and protect employees from potential exposure from silica while cutting bricks with a DeWalt cut off saw exposing the employee to silica.
Recent events (1)
- · Z (S) $0
More inspections in this industry (NAICS 238140)
More inspections in TX
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). OSHA publishes its own view of this case as inspection number 345775993.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.