Safety Incidents OSHA Severe Injury Reports · 2015–2025
3,913,242Inspections Most recent open 2026-07-13 Last loaded 2026-07-17

OSHA Inspection: FOODPREP SOLUTIONS, LLC

Complaint inspection · Safety discipline

On , OSHA opened a complaint safety inspection of FOODPREP SOLUTIONS, LLC in 80 LARGO DRIVE PO BOX 4777, STAMFORD, CT 06907 (NAICS 811411). OSHA activity number 346058753.

Watch Foodprep Solutions, LLC — free Get an email when a new federal OSHA severe-injury report for Foodprep Solutions, LLC is published. One employer, no account, unsubscribe in one click.
Site address
80 LARGO DRIVE PO BOX 4777
City
STAMFORD
State
CT
ZIP
06907
Mailing
80 LARGO DRIVE, STAMFORD, CT 06907
Inspection type
Complaint (B)
Scope
Partial (B)
Discipline
Safety
Advance notice
No
Union status
B
Opened
Closing conference
Case closed
Last modified
Data loaded
NAICS code
811411
Employees
38
Ownership type
A

4 citations on file for this inspection.

1910.133 A03

Serious Gravity 5 1 instance 3 exposed
Issued
Abate by
Penalty
Initial $9324.00 · Current $5250.00 Reduced
29 CFR  1910.133(a)(3):29 CFR 1910.133(a)(3):  The employer did not ensure that each affected employee who wore prescription lenses while engaged in operations that involved eye hazards wore eye protection that incorporated the prescription in its design, or wore eye protection that could be worn over the prescription lenses without disturbing the proper position of the prescription lenses or the protective lenses.  WORKSHOP/PRODUCTION:  On or about July 5, 2022, employees wore their own prescription glasses while grinding knives.  Their glasses did not have side shields and did not meet ANSI Z87.1 requirements to protect the employee from impact.    The employees did not wear safety glasses over their prescription glasses.
Recent events (2)
  • — I (S) $5250
  • — Z (S) $9324

1910.219 C02 I

Serious Gravity 5 2 instances 4 exposed
Issued
Abate by
Penalty
Initial $9324.00 · Current $5250.00 Reduced
29 CFR  1910.219(c)(2)(i): All exposed parts of horizontal shafting seven (7) feet or less from the floor or working platform, except runways used exclusively for oiling, or running adjustments, were not protected by a stationary casing enclosing shafting completely or by a trough enclosing the sides and top or sides and bottom of the shaft as location requires:  WORKSHOP/PRODUCTION:  On or about July 5, 2022, the rotating horizontal shafts of the following standup grinders were unguarded:  1.	Kosher standup grinder, unknown identification unguarded right and left horizontal shafts. 2.	Standup grinder #2, unknown identification unguarded right and left horizontal shafts.
Recent events (2)
  • — I (S) $5250
  • — Z (S) $9324

1910.219 F01 I

Serious Gravity 5 2 instances 4 exposed
Issued
Abate by
Penalty
Initial $0.00 · Current $0.00
29 CFR  1910.219(f)(1)(i):Gears were not guarded by a complete enclosure.   WORKSHOP/PRODUCTION: On or about July 5, 2022, the inner left gear of the Kosher standup grinder, unknown identification, was unguarded.
Recent events (2)
  • — I (S) $0
  • — Z (S) $0

1910.132 D02

Other-than-serious 1 instance 6 exposed
Issued
Abate by
Penalty
Initial $0.00 · Current $0.00
29 CFR  1910.132(d)(2):At this establishment, the employer had not verified that the required workplace hazard assessment had been performed through a written certification that identifies the workplace evaluated; the person certifying that the evaluation had been performed; the dates of the hazard assessment; and which identifies the document as a certification of the hazard assessment.  WORKSHOP/PRODUCTION:  On or about July 5, 2022, the employer had not verified through a written certification that the workplace hazard assessment for personal protective equipment (PPE) had been performed as complete.
Recent events (2)
  • — I (O) $0
  • — Z (O) $0

This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 346058753.