OSHA Inspection: WEBB'S RV CENTER

Issued

May 9, 2023

Abate by

Jun 27, 2023

Penalty

Initial $10,938 · Current $5,469 Reduced

General-duty citation text

29 CFR 1910.28(b)(1)(i): The employer did not ensure that each employee on a walking-working surface with an unprotected side or edge that is 4 feet (1.2 m) or more above a lower level is protected from falling by one or more of the systems described in 29 CFR 1910.28(b)(1)(i):  Throughout the Workshop - The employer did not ensure that employees working on trailer and vehicle roofs with unprotected sides or edges 8-12 feet above a lower level were protected from falling.

Issued

May 9, 2023

Abate by

Jun 5, 2023

Penalty

Initial $4,687 · Current $2,344 Reduced

General-duty citation text

29 CFR 1910.157(e)(2): Portable fire extinguishers were not visually inspected at least monthly:  Throughout the Building - The employer did not ensure that portable fire extinguishers were visually inspected on a monthly basis.

Issued

May 9, 2023

Abate by

Aug 9, 2023

Penalty

Initial $4,687 · Current $2,344 Reduced

General-duty citation text

29 CFR 1910.178(a)(4): Modifications and additions which affect capacity and safe operation of powered industrial truck were performed by the employer without the manufacturer's prior written approval:  Workshop Bay 1 - Employer did not obtain the manufacturer's written approval before using a front-end ball-hitch attachment, which could affect the capacity and safe operation of a Hyundai 30L-7A powered industrial truck.

Issued

May 9, 2023

Abate by

Aug 9, 2023

Penalty

Initial $0 · Current $0

General-duty citation text

29 CFR  1910.178(a)(5): Powered industrial truck(s) equipped with front-end attachments, other than factory installed attachments, were not marked to identify the attachments and show the approximate weight of the truck and attachment combination at maximum elevation with load laterally centered:  Workshop Bay 1 - The Hyundai 30L-7A powered industrial truck, with a ball-hitch attachment, was not marked to identify the attachment and the approximate weight of the powered industrial truck and attachment combination at maximum elevation with load laterally centered.

Issued

May 9, 2023

Abate by

Aug 9, 2023

Penalty

Initial $10,938 · Current $5,469 Reduced

General-duty citation text

29 CFR 1910.178(l)(6): The employer did not certify that each operator has been trained and evaluated as required by this paragraph (l):  Throughout the Workshop - The employer did not certify that the operators, of a Hyundai 30L-7A forklift, had been trained and evaluated.

Issued

May 9, 2023

Abate by

Jun 27, 2023

Penalty

Initial $4,687 · Current $2,344 Reduced

General-duty citation text

29 CFR 1910.303(g)(1)(ii): The required working space about electric equipment rated 600 volts, nominal, or less to ground, was used for storage:   The required working space about electric equipment rated 600 volts, nominal, or less to ground, was used for storage:   a) Unlabeled, Behind Service Counter Beside Exterior Exit Door - Tires and boxes were stored in front of the electrical equipment.  b) PNL-P2, Workshop Bay 1, Nearby Exterior Exit Door - A box and parts were stored in front of the electrical equipment.

Issued

May 9, 2023

Penalty

Initial $0 · Current $0

General-duty citation text

29 CFR  1910.303(b)(2): Listed or labeled equipment was not installed and used in accordance with instructions included in the listing and labeling:  Listed or labeled equipment was not installed and/or used correctly, in the following instances:  a) Workshop Bay 1, Rear Right Corner - The electrical panel door was not closed, as required by the listing and labeling.  b) Service Counter, Rear Right Side - The electrical panel door was not closed, as required by the listing and labeling.  c) Store Front, Office Aisle, Log Column - Extension cords were connected to and from a relocatable power tap (RPT).

Issued

May 9, 2023

Penalty

Initial $7,813 · Current $3,907 Reduced

General-duty citation text

29 CFR 1910.305(b)(2)(i): Each outlet box in completed installations did not have a cover, faceplate, or fixture canopy:  Store Floor, Behind Column - The outlet box, with live wires, did not have a cover plate.

Issued

May 9, 2023

Abate by

Jun 27, 2023

Penalty

Initial $4,687 · Current $2,344 Reduced

General-duty citation text

29 CFR 1910.1200(e)(1): Employer had not developed or implemented a written hazard communication program included the requirements outlined in 29 CFR 1910.1200(e)(1)(i) and (e)(1)(ii):   Webb's RV Center - The employer did not develop or implement a written hazard communication program.

Issued

May 9, 2023

Penalty

Initial $0 · Current $0

General-duty citation text

29 CFR  1910.215(a)(4): Grinding machinery was not used with work rest(s) to support offhand grinding work:   Workshop Bay 1 -  Employees used a DeWalt bench grinder that did not have a work rest to support offhand grinding.

Issued

May 9, 2023

Abate by

Jun 5, 2023

Penalty

Initial $0 · Current $0

General-duty citation text

29 CFR 1910.305(g)(1)(iv)(B): Unless specifically permitted otherwise in paragraph (g)(1)(ii) of this section, flexible cords and cables may not be used to run through holes in walls, ceilings, or floors:  Store Front Offices, On Column Across the Aisle - The employer had a flexible cord and cables run through a wall.

Issued

May 9, 2023

Abate by

Jun 5, 2023

Penalty

Initial $0 · Current $0

General-duty citation text

29 CFR 1910.305(g)(1)(iv)(C): Flexible cords and cables may not be used as a substitute for the fixed wiring of a structure where run through doorways, windows, or similar openings:  Store Front Offices, On Column Across the Aisle - The employer had a flexible cord and cables installed through a hole in the wall, in lieu of fixed wiring.