CANAL WINCHESTER, OH —
OSHA Inspection: KELLOGG CABINETS, INC.
Planned inspection · Health discipline
At a glance
On , OSHA opened a planned health inspection of KELLOGG CABINETS, INC. in 7711 DILEY ROAD, CANAL WINCHESTER, OH 43110 (NAICS 337212). OSHA activity number 346515968.
OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- KELLOGG CABINETS, INC.
- Site address
- 7711 DILEY ROAD
- City
- CANAL WINCHESTER
- State
- OH
- ZIP
- 43110
- Mailing
- 7711 DILEY ROAD, CANAL WINCHESTER, OH 43110
What kind of inspection was it?
- Inspection type
- Planned (H)
- Scope
- Partial (B)
- Discipline
- Health
- Advance notice
- No
- Union status
- B
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 337212
- Employees
- 11
- Ownership type
- A
Citations
2 citations on file for this inspection.
1910.213 C02
- Issued
- Mar 27, 2023
- Abate by
- Apr 13, 2023
- Penalty
- Initial $3,572 · Current $2,500 Reduced
General-duty citation text
29 CFR 1910.213(c)(2):Each hand-fed circular ripsaw shall be furnished with a spreader to prevent material from squeezing the saw or being thrown back on the operator. The spreader shall be made of hard tempered steel, or its equivalent, and shall be thinner than the saw kerf. It shall be of sufficient width to provide adequate stiffness or rigidity to resist any reasonable side thrust or blow tending to bend or throw it out of position. The spreader shall be attached so that it will remain in true alignment with the saw even when either the saw or table is tilted. The provision of a spreader in connection with grooving, dadoing, or rabbeting is not required. On the completion of such operations, the spreader shall be immediately replaced. a. On or about February 23, 2023, in the Milling Department, the Powermatic Table Saw #1 was not equipped with a spreader to prevent the material from squeezing the saw. b. On or about February 23, 2023, in the Production Department, the Powermatic Table Saw #13 was not equipped with a spreader to prevent the material from squeezing the saw. c. On or about February 23, 2023, in the Milling Department, the Altendork Table Saw #9 was not equipped with a spreader to prevent the material from squeezing the saw.
Recent events (2)
- — I (S) $2500.4
- — Z (S) $3572
1910.213 C03
- Issued
- Mar 27, 2023
- Abate by
- Apr 13, 2023
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.213(c)(3): Each hand-fed circular ripsaw shall be provided with nonkickback fingers or dogs so located as to oppose the thrust or tendency of the saw to pick up the material or to throw it back toward the operator. They shall be designed to provide adequate holding power for all the thicknesses of materials being cut. a. On or about February 23, 2023, in the Milling Department, the Powermatic Table Saw #1 was not equipped with nonkickback fingers to prevent the material from kicking back at the operator. b. On or about February 23, 2023, in the Production Department, the Powermatic Table Saw #13 was not equipped with nonkickback fingers to prevent the material from kicking back at the operator. c. On or about February 23, 2023, in the Milling Department, the Altendork Table Saw #9 was not equipped with nonkickback fingers to prevent the material from kicking back at the operator.
Recent events (2)
- — I (S) $0
- — Z (S) $0
More inspections at Kellogg Cabinets, INC.
View Kellogg Cabinets, INC.'s full OSHA safety record →
More inspections in this industry (NAICS 337212)
More inspections in OH
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 346515968.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.