SPRING VALLEY, NY ·
OSHA Inspection: SD TRIM LLC
Programmed Related inspection · Safety discipline
At a glance
On , OSHA opened a programmed Related safety inspection of SD TRIM LLC in 575 UNION RD., SPRING VALLEY, NY 10977 (NAICS 238350). OSHA activity number 346612781.
OSHA opens inspections for many reasons: routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- SD TRIM LLC
- Site address
- 575 UNION RD.
- City
- SPRING VALLEY
- State
- NY
- ZIP
- 10977
- Mailing
- 4 TRUMAN DRIVE, STONY POINT, NY 10980
What kind of inspection was it?
- Inspection type
- Programmed Related (I)
- Scope
- Complete (A)
- Discipline
- Safety
- Advance notice
- No
- Union status
- Non-union (B)
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 238350
- Employees
- 2
- Ownership type
- Private (A)
Citations
2 citations on file for this inspection.
1926.404 B01 I
- Issued
- Jul 31, 2023
- Penalty
- Initial $3,349 · Current $2,344 Reduced
General-duty citation text
29 CFR 1926.404(b)(1)(i): General. The employer did not use either ground fault circuit interrupters as specified in paragraph (b)(1)(ii) of this section or an assured equipment grounding conductor program as specified in paragraph (b)(1)(iii) of this section to protect employees on construction sites. These requirements are in addition to any other requirements for equipment grounding conductors: location: 1st and 2nd floor on or about: 5/6/19 a) Employees were using electrical equipment, including a Makita circular saw, while engaged in carpentry trim work. The employees were not provided with GFCI protection or an assured equipment grounding conductor program. NOTE: Because abatement of this violation is already documented in the inspection casefile, the employer need not submit certification or documentation of abatement for this violation as normally required by 29 CFR 1903.19.
Recent events (2)
- · I (S) $2344
- · Z (S) $3349
1926.1052 C01 II
- Issued
- Jul 31, 2023
- Penalty
- Initial $2,009 · Current $1,406 Reduced
General-duty citation text
29 CFR 1926.1052(c)(1)(ii): Stairways having four or more risers or rising more than 30 inches (76 cm), whichever is less, were not equipped with a stairrail system along each unprotected side or edge: location: between 1st floor and 1st floor landing on or about: 3/8/23 a) Employees used the stairs for access between the first and 2nd floor. The 6 riser stairs between the 1st floor and 1st floor landing did not have a stairrail system along one of the the open sides. NOTE: Because abatement of this violation is already documented in the inspection casefile, the employer need not submit certification or documentation of abatement for this violation as normally required by 29 CFR 1903.19.
Recent events (2)
- · I (S) $1406
- · Z (S) $2009
More inspections in this industry (NAICS 238350)
More inspections in NY
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). OSHA publishes its own view of this case as inspection number 346612781.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.