NACOGDOCHES, TX —
OSHA Inspection: STRAIGHT CUT LUMBER
Complaint inspection · Health discipline
At a glance
On , OSHA opened a complaint health inspection of STRAIGHT CUT LUMBER in 8525 S US HWY 59, NACOGDOCHES, TX 75964 (NAICS 321912). OSHA activity number 347066938.
What this inspection record means
OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Watch Straight CUT Lumber — free
Get an email when a new federal OSHA severe-injury report for Straight CUT Lumber is published. One employer, no account, unsubscribe in one click.
Where did this inspection happen?
- Establishment
- STRAIGHT CUT LUMBER
- Site address
- 8525 S US HWY 59
- City
- NACOGDOCHES
- State
- TX
- ZIP
- 75964
- Mailing
- 8525 S US HWY 59, NACOGDOCHES, TX 75964
What kind of inspection was it?
- Inspection type
- Complaint (B)
- Scope
- Partial (B)
- Discipline
- Health
- Advance notice
- No
- Union status
- B
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 321912
- Employees
- 12
- Ownership type
- A
Citations
10 citations on file for this inspection.
1910.28 B06 II
- Issued
- Jan 17, 2024
- Abate by
- Feb 5, 2024
- Penalty
- Initial $6,452 · Current $2,258 Reduced
General-duty citation text
29 CFR 1910.28(b)(6)(ii): The employer did not ensure that each employee 4 feet (1.2 m) or more above dangerous equipment must be protected from falling by one of the systems listed in 29 CFR 1910.28(b)(6)(ii)(A)-(D): On or about October 26, 2023, on the south side of the mill where employees were exposed to a fall onto dangerous equipment hazard while walking by a hole in the ground with an exposed auger in it without any form of guarding.
Recent events (2)
- — I (S) $2258.2
- — Z (S) $6452
1910.95 C01
- Issued
- Jan 17, 2024
- Abate by
- Feb 5, 2024
- Penalty
- Initial $4,610 · Current $1,614 Reduced
General-duty citation text
29 CFR 1910.95(c)(1): The employer did not administer a continuing, effective hearing conservation program as described in 29 CFR 1910.9(c) through (o) whenever employee noise exposures equal or exceed an 8-hour time-weighted average sound level of 85 decibels measured on the A scale, or equivalently a dose of fifty percent: On or about October 26, 2023, throughout the mill where employees were exposed to eight-hour time weighted averages between 95.8 and 88.5 decibels before an effective hearing conservation program had been implemented.
Recent events (2)
- — I (S) $1613.5
- — Z (S) $4610
1910.141 D02 II
- Issued
- Jan 17, 2024
- Abate by
- Feb 5, 2024
- Penalty
- Initial $2,765 · Current $0 Reduced
General-duty citation text
29 CFR 1910.141(d)(2)(ii): Lavatories were not provided with hot and cold, or tepid running water: On or about October 26, 2023, and at times prior thereto, at the facility where employees were exposed to contact and ingestion hazards when using portable toilets without having accessible hot or tepid water for hand washing.
Recent events (2)
- — I (S) $0
- — Z (S) $2765
1910.212 A03 II
- Issued
- Jan 17, 2024
- Abate by
- Feb 5, 2024
- Penalty
- Initial $6,452 · Current $2,258 Reduced
General-duty citation text
29 CFR 1910.212(a)(3)(ii): Point(s) of operation of machinery were not guarded to prevent employee(s) from having any part of their body in the danger zone(s) during operating cycle(s): On or about October 26, 2023, on the south side of the mill where employees were exposed to struck-by hazards while working near the chipper machine without a guard to protect the employees from falling onto the conveyor belt that led to the blade wheel.
Recent events (2)
- — I (S) $2258.2
- — Z (S) $6452
1910.219 D01
- Issued
- Jan 17, 2024
- Abate by
- Feb 5, 2024
- Penalty
- Initial $4,610 · Current $1,614 Reduced
General-duty citation text
29 CFR 1910.219(d)(1): Pulley(s) with part(s) seven feet or less from the floor or work platform were not guarded in accordance with the requirements specified in 29 CFR 1910.219(m) and (o): On or about October 26, 2023: a. On the north side of the mill saw where employees were exposed to a caught-by hazard while working near the mill conveyor without a guard to cover the out-feed belt pulley. b. On the east side of the edger saw where employees were exposed to a caught-by hazard while working near the edger conveyor without a guard cover the belt pulley. c. On the north side of the chipper conveyor where employees were exposed to a caught-by hazard while working near the chipper conveyor end pulley without a guard to cover the belt pulley. d. On the south side of the chipper where employees were exposed to a caught-by hazard while working near the chipper motor without a guard to cover the chipper motor pulleys.
Recent events (2)
- — I (S) $1613.5
- — Z (S) $4610
1910.219 E01 I
- Issued
- Jan 17, 2024
- Abate by
- Feb 5, 2024
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.219(e)(1)(i): Horizontal belts which had both runs seven feet or less from the floor level were not guarded with a guard that extended to at least fifteen inches above the belt: On or about October 26, 2023: a. On the north side of the mill saw where employees were exposed to a caught-by hazard while working near the mill conveyor without a guard to cover the out-feed belt. b. On the east side of the edger saw where employees were exposed to a caught-by hazard while working near the edger conveyor without a guard cover the belt. c. On the north side of the chipper conveyor where employees were exposed to a caught-by hazard while working near the chipper conveyor end pulley without a guard to cover the belt. d. On the south side of the chipper where employees were exposed to a caught-by hazard while working near the chipper motor without a guard to cover the chipper motor belts.
Recent events (2)
- — I (S) $0
- — Z (S) $0
1904.29 B03
- Issued
- Jan 17, 2024
- Abate by
- Feb 5, 2024
- Penalty
- Initial $922 · Current $0 Reduced
General-duty citation text
29 CFR 1904.29(b)(3): Each recordable injury or illness was not entered on the OSHA 300 Log and/or an incident report (OSHA Form 301or equivalent) within seven (7) calendar days of receiving information that a recordable injury or illness has occurred: On or about October 11, 2023, at the facility where an employee was injured on September 28, 2023 resulting in a hospitalization that was not listed on the 2023 OSHA 300 Log or an OSHA form 301.
Recent events (2)
- — I (O) $0
- — Z (O) $922
1904.39 A02
- Issued
- Jan 17, 2024
- Abate by
- Jan 23, 2024
- Penalty
- Initial $4,610 · Current $1,614 Reduced
General-duty citation text
29 CFR 1904.39(a)(2): The employer did not report within 24-hours a work-related incident resulting in in-patient hospitalization, amputation or the loss of an eye. On or about September 18, 2023, an employee was hospitalized following a work-related injury and the incident was not reported within 24 hours.
Recent events (2)
- — I (O) $1613.5
- — Z (O) $4610
1910.1200 E01
- Issued
- Jan 17, 2024
- Abate by
- Feb 5, 2024
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.1200(e)(1): The employer did not develop, implement, and/or maintain at the workplace a written hazard communication program which describes how the criteria specified in 29 CFR 1910.1200(f), (g), and (h) will be met: On or about October 26, 2023, and at times prior thereto, throughout the mill where employees were required to handle hazardous chemicals before a written hazard communication program had been developed and implemented.
Recent events (2)
- — I (O) $0
- — Z (O) $0
1910.1200 F06 II
- Issued
- Jan 17, 2024
- Abate by
- Feb 5, 2024
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.1200(f)(6)(ii): Except as provided in 29 CFR 1910.1200(f)(7) and 29 CFR 1910.1200(f)(8), the employer did not ensure that each container of hazardous chemicals in the workplace was labeled, tagged or marked with the product identifier and words, pictures, symbols, or combination thereof, which provide at least general information regarding the hazards of the chemicals and which, in conjunction with the other information immediately available to employees under the hazard communication program, would provide employees with the specific information regarding the physical and health hazards of the hazardous chemical: On or about October 26, 2023, next to the trim saw where employes were using what was thought to be hydraulic oil in sports drink and water bottles, without any form of label or markings as to the chemicals identity
Recent events (2)
- — I (O) $0
- — Z (O) $0
More inspections at Straight CUT Lumber
View Straight CUT Lumber's full OSHA safety record →
More inspections in this industry (NAICS 321912)
Jul 7, 2026
161497 - C.L. Loven Lumber CO., INC. · PINEOLA, NC
Jul 6, 2026
111530 - Rich Prairie Custom Woods LLC · PIERZ, MN
Jun 18, 2026
317744567 - Western Valley Cutstock INC · WHITE CITY, OR
Jun 10, 2026
AFP Logs and Lumber INC. · BUCKHANNON, WV
Jun 4, 2026
Northwest Hardwoods INC · BYRON CENTER, MI
More inspections in TX
Jul 17, 2026
Cornelius Nurseries, INC. · RICHMOND, TX
Jul 17, 2026
Holloway Houston, INC. · HOUSTON, TX
Jul 17, 2026
Voluntary Purchasing Groups, INC. · BONHAM, TX
Jul 16, 2026
Rnwbl · SNYDER, TX
Jul 16, 2026
United Rentals, INC. · WICHITA FALLS, TX
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 347066938.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.